GE Ice Maker Parts

Condenser Fan Motor Kit

3 Reviews

Part Number: W10124096

This fan motor is used in frost-free refrigerators with a condenser coil. When the compressor runs, so does this fan, circulating air through the refrigerator grille, to cool the compressor and condenser coils. This fan motor also helps to evaporate excess water in the drain pan. This kit includes the motor, fan blade, wire harness, and screw. If your refrigerator/freezer section is too warm you may need to replace this part. This part has been updated by the manufacturer. It may look different in appearance but will still function the same as the original part. This is a genuine OEM part. Disconnect power to your refrigerator before starting the repair.

Silicone Rubber Adhesive - 2 oz

Part Number: WP279368

This 2oz high temperature silicone rubber adhesive is used to create a water tight seal for gaskets and felt seals. The working surface must be clean, dry and free from any type of oil or grease. This is a genuine OEM part. It is recommended to wear gloves to protect your hands while working with the adhesive.

Grommet / Tube Assembly

1 Review

Part Number: WR17X11168

This is a replacement fill tube and grommet assembly for your refrigerator. This part acts your water line to your ice maker. If you’re noticing water in the back of the refrigerator or any kind of leak, or if your ice bucket isn’t filling up with as much ice, you may need to change out the fill tube and grommet assembly. When you purchase this part, you get the water line, as well as the fill tube and grommet. This is an OEM part sourced directly from the manufacturer.

Water Tube Kit

Part Number: W10823511

The water tubing is made of plastic and goes between the water valve and the back of your refrigerator. The tubing is 72” in length, 1/4 inch in diameter, and comes with 2 inserts. This tube may be longer than the original tube and may need to be cut to fit your appliance. The water tube transports water to the ice and water dispensers. If there is no water going to the ice maker, your refrigerator is leaking, or if the ice and water dispensers are not dispensing properly, you may need to replace this tube kit. This part is an OEM part directly from the manufacturer. Please remember to shut off the water supply and to disconnect the power to your refrigerator before starting your repair.

Water Inlet Valve with Quick Connections - 120V 60Hz

Part Number: W10881366

Used with freestanding ice cube makers.

Ice Maker Water Distributor Tube

Part Number: W10863947

The water distributor tube distributes water from the reservoir to the evaporator plate.

GROMMET

Part Number: W10852725

Door Light Switch

Part Number: WP2149705

The white door light switch is in the control panel section of your refrigerator. The light will turn on when you open the door. If the light doesn?t turn on when the door is open the contacts in the switch could be burnt out and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power to your refrigerator before starting your repair.

Thermistor

2 Reviews

Part Number: WPW10503764

If your standalone ice maker is making too much ice, not enough ice, or none, you may need to replace the bin thermostat. This part will sense how much ice is in the bin and decide if it should produce more or stop the production of ice. You can test the thermostat for continuity with an ohm meter. This part is made of metal and plastic and is white in color. This is a genuine OEM part.

Refrigerator Water Filter

1 Review

Part Number: GSWF

This OEM filter is sold individually. Change your filter every 6 months for the best results. This filter is found in top-freezer and bottom-freezer refrigerators located in the back upper right corner. It measures 4.75-Inches deep, 9.5-Inches high, and 5.25-Inches wide. It is certified to reduce particles, chlorine-resistant cysts, lead and five other impurities. The pressure requirement is 40-120 PSI (if yours exceeds this, you?ll need to install a pressure-timing valve), and the operating temperature needs to be 33-100 degrees Fahrenheit. It filters down to 0.5-1 microns. The installation is simple and does not require any tools or mess. To remove the old cartridge, turn it to the left and pull down carefully. Some water might drip, so keep a cloth handy. To install the new filter, place it into the cartridge holder and turn to the right until it will no longer turn. If you have a top-freezer model it should be situated vertically, and if it is a bottom-freezer model, it should be placed horizontally. Be careful not to over-tighten. If your model has a replacement indicator light, reset it by pushing and holding it down for three seconds. If your model has a dispenser, run water through it for approximately 3 minutes to clear the system. Please note that this filter will not work in Kenmore brand models.