Jenn-Air Washer Parts

Belt Kit

20 Reviews

Part Number: 12112425

There are two belts under a Maytag washer; one for the main drive pulley and one for the water pump. The belt kit includes both the drive belt and the pump belt which are both "V" shaped. The belt connects the drive motor to the drive system to be able to spin the tub basket. If your washer will not agitate, not spin, or not drain, the belt could be worn or damaged and will need to be replaced. This is a genuine OEM kit. Please remember to disconnect the power and shut off the water supply to your washer before starting your repair.

Drive Belt - 51 inches long

3 Reviews

Part Number: WP21352320

This V-style drive belt is about 51-inch long and 3/8-inch wide. This part is made to slip onto the motor pulley to bring the basket up to the speed required. The belt encounters wear and tear over time. If your washer will not drain, spin, or agitate, you may need to replace your belt. It is recommended to disconnect the power to your washer before you start your repair. This V-style belt is a genuine OEM part.

Lid Hinge Pin

4 Reviews

Part Number: WP35-2045

The lid hinge pin allows the lid to pivot open and closed correctly. This part is the male end of the lid hinge. If the lid is not opening or closing properly you may need to replace the lid hinge pin on your washer. This lid hinge pin is just over an inch long. It is all white in color and is made entirely of plastic.

Agitator Drive Shaft Seal

1 Review

Part Number: WP6-0A57420

This shaft seal comes filled with grease on the inside, and is used for washing machines.

Tub Bearing Kit

3 Reviews

Part Number: 6-2040130

The tub bearing kit is used on 2-belt washers. This part helps keep the interior tub spinning correctly. If your washer is leaking, noisy, or shakes and moves, you may need to replace the tub bearing. It is recommended to change the seal kit at the same time you are replacing the tub bearing. This is a genuine OEM part. Remember to disconnect the power and shut off the water supply to the washer before starting your repair.

Transmission Pulley and Bearing Kit

12 Reviews

Part Number: 12002213

The transmission pulley and bearing kit, also known as a thrust bearing kit, is located on the drive shaft. If your washer won’t agitate during use, drum won’t drain, or there is a loud noise during operation, you may need to replace this part. A worn bearing also causes slow spinning or no spin at all. This kit includes the pulley that rotates to spin the tub, washer, and thrust bearing that fits between the pulley and the transmission shaft, 2 upper race washers, 1 lower race washer and the instruction sheet. This is a genuine OEM kit; the parts are not available separately. Please remember to disconnect the power and water supply to the washer before starting the repair.

Snubber Ring

4 Reviews

Part Number: WP21002026

The snubber ring works in conjunction with your washing machine by helping to reduce noise and vibration during operation. The snubber ring fits between the leg and washer base. It is white in color, and measures approximately 8 1/2” in diameter. If your washer is making a loud noise or shakes a lot during use, the snubber ring may need to be replaced. Disconnect the power and water supply before beginning your repair. This is a genuine OEM part.

Lid Hinge

2 Reviews

Part Number: WP35-2044

The lid hinge attaches to the lid of your washer to allow the lid to pivot open and closed when in use. This part is the female end of the lid hinge. The lid hinge is an inch and a half long. It is all white in color and is made entirely of plastic.

Drain Pump

8 Reviews

Part Number: WP6-2022030

This washing machine drain pump is intended for use with automatic washers that have been manufactured since 1958. The pump itself is made of plastic, though it does come with a metallic belt pulley.

Drive Motor - One Speed - 120V

2 Reviews

Part Number: 12002351