Frigidaire Refrigerator FRS26H5ASB5
Repairing your FRS26H5ASB5 Frigidaire Refrigerator is simple with official replacement parts made to fit your model. View a selection of popular parts, or review parts lists for each of the
FRS26H5ASB5 model diagrams below. Trust us to help you find the part you need and get your
FRS26H5ASB5 Frigidaire Refrigerator running again.
Diagrams for Frigidaire FRS26H5ASB5 Refrigerator
There are 12 diagrams for FRS26H5ASB5. Click on the diagram where you think your part is located.
Most Popular FRS26H5ASB5 Parts
These are the most commonly purchased repair parts for FRS26H5ASB5.
-
(13)
When energized, the water inlet valve will release water from the supply line into the ice mold and the water dispenser in the refrigerator. If the ice maker is not making or dispensing ice, not dispensing water, or leaking, you may need to replace the water inlet valve. The water inlet valve is in the back section of your refrigerator and will need to be pulled out from the wall. Make sure to disconnect both the water and power supply before starting your repair. NOTE: This part may appear different than the original but is an authorized manufacturer replacement.
-
(7)
This replacement drawer slide rail is for the right-hand side of your refrigerator. This part attaches to the inside wall of your refrigerator to support the sliding crisper drawer. If the rail is broken or the drawer is not sliding properly, you will need to replace the slide rail. You will need a Phillips screwdriver to complete this repair.
-
(10)
The ice maker assembly is used to produce ice for your refrigerator. The ice maker receives water from the water inlet valve and will freeze until ice cubes are formed. Once the water has been frozen the cubes will be ejected from the mold into the ice bucket. The ice maker will continue the process until the ice bucket has reached the limit. If your ice maker is not making ice you may need to replace this part. This kit includes the fill cup, 4 pin wire harness adapter, and tube. Please remember to disconnect the power and water supply before starting your repair. This ice maker is a genuine OEM part.
-
(1)
Mounting screws NOT included.
-
(2)
If your refrigerator or freezer is too warm or making noises, you may need to replace the fan blade. The fan blade attaches to the evaporator motor, which is in the freezer section, to help circulate the cold air into the refrigerator and freezer sections. The fan blade is white in color and made from plastic. This is a genuine OEM part. Please be sure to disconnect the power to your refrigerator before starting your repair.
-
(3)
Compressor start relay kit is an original equipment manufacturer (OEM) part that fits some Kenmore, Frigidaire, Electrolux, Crosley, Gibson and White-Westinghouse refrigerators. It also fits some Kenmore, Frigidaire and Gibson upright freezers.
Compressor start relay kit includes the compressor start relay, run capacitor, wire harness adapter, 2 wire terminals, 2 wire connectors, 2 pieces of wire connection shrink tubing, the wire retaining clip and kit instructions sheet.
Clarification of instructions: Kit 5304491941 now uses a wire harness with white wires; attach the red compressor power wire to the wire harness adapter's white wire that plugs into the start device terminal at the outside edge of the start device.
Replaces original refrigerator and freezer compressor start relay part numbers 216649316, 218721119, 241524601, 241524605 and 5304468029.
Fits some refrigerators in the following series: Kenmore and Kenmore Elite 253; Frigidaire FRS, FRT, FRX, FSC, GLH, GLR, GS2, NGS, PHS, PLH and PLRS; Electrolux E23; Crosley CRSE; Gibson GRS and GRT; and White-Westinghouse WRS and WRT. Also fits some upright freezers in these series: Kenmore 253; Frigidaire FFU; and Gibson GFU.