Westinghouse Refrigerator WRS6R3EW0
Repairing your WRS6R3EW0 Westinghouse Refrigerator is simple with official replacement parts made to fit your model. View a selection of popular parts, or review parts lists for each of the
WRS6R3EW0 model diagrams below. Trust us to help you find the part you need and get your
WRS6R3EW0 Westinghouse Refrigerator running again.
Diagrams for Westinghouse WRS6R3EW0 Refrigerator
There are 12 diagrams for WRS6R3EW0. Click on the diagram where you think your part is located.
Most Popular WRS6R3EW0 Parts
These are the most commonly purchased repair parts for WRS6R3EW0.
-
(13)
When energized, the water inlet valve will release water from the supply line into the ice mold and the water dispenser in the refrigerator. If the ice maker is not making or dispensing ice, not dispensing water, or leaking, you may need to replace the water inlet valve. The water inlet valve is in the back section of your refrigerator and will need to be pulled out from the wall. Make sure to disconnect both the water and power supply before starting your repair. NOTE: This part may appear different than the original but is an authorized manufacturer replacement.
-
(2)
This 40-watt light bulb has a standard screw-in base and is used in many different appliances. If your current bulb is burnt out or broken you will need to replace it. This light bulb is a genuine OEM part and is sold individually.
-
(10)
The ice maker assembly is used to produce ice for your refrigerator. The ice maker receives water from the water inlet valve and will freeze until ice cubes are formed. Once the water has been frozen the cubes will be ejected from the mold into the ice bucket. The ice maker will continue the process until the ice bucket has reached the limit. If your ice maker is not making ice you may need to replace this part. This kit includes the fill cup, 4 pin wire harness adapter, and tube. Please remember to disconnect the power and water supply before starting your repair. This ice maker is a genuine OEM part.
-
(4)
This is a replacement condenser fan motor kit for your refrigerator. This six-piece kit contains foam tape, 2 screws, the fan blade, the new motor mounting bracket, and the condenser fan motor. The condenser fan motor is found in the back of the refrigerator, and it moves air across the compressor and the condenser to keep them cool. If the motor has failed, the condenser and the compressor will run hot, and this can cause the refrigerator not to cool. This is an OEM part from the manufacturer.
-
(3)
Compressor start relay kit is an original equipment manufacturer (OEM) part that fits some Kenmore, Frigidaire, Electrolux, Crosley, Gibson and White-Westinghouse refrigerators. It also fits some Kenmore, Frigidaire and Gibson upright freezers.
Compressor start relay kit includes the compressor start relay, run capacitor, wire harness adapter, 2 wire terminals, 2 wire connectors, 2 pieces of wire connection shrink tubing, the wire retaining clip and kit instructions sheet.
Clarification of instructions: Kit 5304491941 now uses a wire harness with white wires; attach the red compressor power wire to the wire harness adapter's white wire that plugs into the start device terminal at the outside edge of the start device.
Replaces original refrigerator and freezer compressor start relay part numbers 216649316, 218721119, 241524601, 241524605 and 5304468029.
Fits some refrigerators in the following series: Kenmore and Kenmore Elite 253; Frigidaire FRS, FRT, FRX, FSC, GLH, GLR, GS2, NGS, PHS, PLH and PLRS; Electrolux E23; Crosley CRSE; Gibson GRS and GRT; and White-Westinghouse WRS and WRT. Also fits some upright freezers in these series: Kenmore 253; Frigidaire FFU; and Gibson GFU.
-
(2)
This is a replacement crisper glass insert for your refrigerator. It fits into the crisper pan frame and acts as the top of the crisper pan, as well as a shelf for food storage. Because it is made of glass, the insert can occasionally become cracked or broken, and in this case, it will need to be replaced. To replace the insert, simply slide the old insert out and replace it with the new one. The glass insert measures approximately 17.12" X 15.40", and is sold individually. This is an OEM part sourced directly from the manufacturer.