Amana Washer Parts

Hose Clamp

Part Number: WP285655

This single hose clamp is used to hold the water hose in place on the pump, to avoid the hose or pump from leaking water. If you notice your washer leaking you may need to replace the clamp. Please remember to disconnect the power and water supply before starting your repair. This is a genuine OEM part.

Hose Clamp

Part Number: WP596669

This hose clamp expands from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag washing machines to secure the end of the drain hose to the pump drain port. Please make sure to disconnect the power to your washer before you start your repair. This hose clamp is a genuine OEM part and is sold individually.

Transmission Pulley and Bearing Kit

11 Reviews

Part Number: 12002213

The transmission pulley and bearing kit, also known as a thrust bearing kit, is located on the drive shaft. If your washer won’t agitate during use, drum won’t drain, or there is a loud noise during operation, you may need to replace this part. A worn bearing also causes slow spinning or no spin at all. This kit includes the pulley that rotates to spin the tub, washer, and thrust bearing that fits between the pulley and the transmission shaft, 2 upper race washers, 1 lower race washer and the instruction sheet. This is a genuine OEM kit; the parts are not available separately. Please remember to disconnect the power and water supply to the washer before starting the repair.

Washer Drive Pulley

2 Reviews

Part Number: W10721967

This is a replacement clutch assembly or cam kit for your washer. The clutch assembly is mounted on the drive shaft on the bottom of your washer. You may need to replace the clutch assembly if the splines on the clutch assembly are stripped and the washer is making noise, or if you are having problems with the wash and spin cycles. You will need to access the bottom of the washer for this repair. It is easiest to if you disconnect your washer from both the water and power source, and lay it on its back. The clutch assembly contains 6 parts, and all are included with the kit. It is also important to change out the entire assembly, rather than individual pieces.

Thrust Washer

Part Number: WP233520

This part is located between the drum support rollers and idler pulley in your dryer to help prevent the parts from bumping up against the brackets they are attached to. If your dryer has a burning smell, is noisy, or will not tumble, you may need to replace the thrust washer. The washer is 3/4 inches in diameter and a is genuine OEM part. It is recommended to disconnect the power to your dryer before you start your repair.

Suspension Spring

Part Number: WP63907

This suspension spring is used to support and balance the outer tub of your washer. If the spring is broken it will cause the washer to be off balance and noisy. Check your model to see how many springs are required for your model. The spring is sold individually.

Snubber Ring

4 Reviews

Part Number: WP21002026

The snubber ring works in conjunction with your washing machine by helping to reduce noise and vibration during operation. The snubber ring fits between the leg and washer base. It is white in color, and measures approximately 8 1/2” in diameter. If your washer is making a loud noise or shakes a lot during use, the snubber ring may need to be replaced. Disconnect the power and water supply before beginning your repair. This is a genuine OEM part.

Direct Drive Motor Coupling

29 Reviews

Part Number: 285753A

The newer version of the coupler kit is made with new metal sleeves for added strength. This part is located between the motor and transmission on the direct drive washer that does not have a belt. The coupler will break to protect the motor from damage if the drive motor system seizes up. If your washer will not fill, will not agitate or spin, but it will drain the water from the tub, you may need to replace this part because it has failed. This is a genuine OEM part. Disconnect the power to your washer before starting the repair.

Touch-Up Paint - White

2 Reviews

Part Number: 72017

This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, and freezers. This is a genuine OEM part and includes a brush applicator. Please remember to wear gloves to protect your hands when applying this paint.

Drain Pump with Pulley

10 Reviews

Part Number: WP35-6465

This drain pump with pulley has 2 ports. The pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period. If your washer will not drain, is noisy, leaking or has a burning smell, you may need to replace the drain pump. This is a genuine OEM part. Please remember to shut off the water supply and disconnect the power to the washer before starting your repair.