Hotpoint Washer Parts

Tub Dampening Strap

Part Number: WH1X2727

This part is used to support the tub and keep it in the center of the cabinet to reduce vibration. If your washer is making loud noises, or shakes or moves, one or more of the straps may have broken. It is recommended to replace all 4 tub dampening straps at the same time. This part is sold individually.

D-Shaped Knob Clip

1 Review

Part Number: WH01X10106

This control knob clip helps secure the timer knob to the shaft allowing you to select the desired setting for your dryer. If the knob has become loose or the clip is missing you will need to replace the clip. This clip is a genuine OEM part, made of metal and is sold individually.

Drain Hose

Part Number: WH41X10096

This corrugated drain hose carries the drain water from the washer to the house drain. It is black in color, measures 57” long, and both ends of the drain hose can be bent. If your drain hose becomes damaged or cracked, it will cause water to leak on the floor during the wash cycle and you will need to replace the hose. This is a genuine OEM part. Please make sure you shut off the water supply and disconnect the power to the washer before starting your repair. Note: Clip is not included.

Agitator Coupling Kit

5 Reviews

Part Number: WH49X10042

This is a washing machine agitator coupling kit also known as an agitator drive belt. It connects the transmission drive shaft to the agitator base. It includes the couple, gasket, and bolt. If the teeth on the coupler is worn out it will cause the agitator not to turn and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power before starting your repair.

Dual Water Inlet Valve

Part Number: WH13X10024

This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.

Tub Bearing

Part Number: WH2X1198

This tub bearing goes in your washing machine. You will find it on the bottom of the outer tub, where the transmission goes through the tub. If you hear metal on metal when the washer is spinning, you may need to replace the tub bearing. This bearing is made of metal, and is approximately 3 inches wide and 2 inches tall.

Tub Seal

1 Review

Part Number: WH02X10383

The tub seal helps prevent any leaking around the transmission of your washer outer tub. If your washer is leaking you may need to replace the seal. The tub seal is located on the bottom of the outer tub, in the center where the transmission comes through to connect to the agitator. This is a genuine OEM part. It is suggested to have it installed by a qualified technician because the seal can be difficult to replace. Please remember to shut off the water supply and disconnect the power to the washer before starting your repair.

Tub Bearing Washer

Part Number: WH2X1197

The tub bearing washer goes between the transmission and the tub bearing in your washer. This part helps to keep the inner tub spinning smoothly during operation. If your washer is noisy you may hear the bearing wearing on the transmission and the tub bearing washer will need to be replaced. This part is gray in color and measures approximately 2” in diameter. This is a genuine OEM part. Please disconnect the power and water supply to the washer before starting this repair.

Lid Switch Actuator

Part Number: WH1X2734

This is part of the lid switch actuator mechanism and activates the lid switch, when the lid is closed, to start the wash cycle and when the lid is open, it stops the cycle.

Dual Action Agitator

11 Reviews

Part Number: WH43X10034

This plastic dual action agitator is white in color. It is approximately eighteen inches tall with a base diameter of about 12-1/4 inches. The agitator pivots back and forth, moving the clothes from the top to the bottom of the tub, through the detergent and water to wash them. If the agitator becomes damaged or will not agitate, you may need to replace the part. This is a genuine OEM part. Please remember to shut off the water supply and disconnect the power to the washer before starting your repair.