Inglis Appliance Parts

Refrigerator Center Crisper Drawer Slide Rail - White

134 Reviews

Part Number: WPW10671238

This is the center support rail for the crisper drawers. The rail attaches to the shelf frame between the two crisper drawers to provide support for the drawers as they slide in and out. The support rail is white in color and made of plastic. It measures approximately 13.5-inches in length and is a genuine OEM part.

Rack Track Stop

32 Reviews

Part Number: WP8565925

This gray rack track stop is used for your upper dish rack track to prevent the rack from sliding off the slide rail. If your rack is falling off the track, you may need to replace the track stop. This is a genuine OEM part and is sold individually.

Dryer Repair Kit

40 Reviews

Part Number: 4392067

This dryer repair kit consists of five commonly replaced dryer parts: one multi-rib belt (part #661570V and measures 93 1/2 inches long), four drum support rollers, one idler assembly, nine tri-rings, and one washer. This universal maintenance kit is an all-encompassing kit for fixing a noisy dryer, among other symptoms, but noisy being the most common. It is compatible with 27-inch wide dryers built from 1965 onwards. Be sure to disconnect the dryer or shut off the house circuit breaker for the appliance before you begin your repair. To access these parts, you will need to remove the dryer drum. For this installation you will need a 1/4-inch nut driver, a long flat-blade screwdriver, a short flat-blade screw diver, and a Phillips screwdriver.

Refrigerator Crisper Drawer with Humidity Control

35 Reviews

Part Number: WP2188656

This clear crisper drawer with humidity control allows you to adjust the humidity within the crisper. This can extend the life of your produce. Does the drawer measure approximately 7.60 inches in height by 14.92 inches from front to back and 16.50 inches wide. This is a genuine OEM part.

Heating Element - 5300W

Part Number: DC47-00019A

Includes the insulators and restring already attached. This dryer heating element produces heat to dry clothes in a dryer and is located in the rear end. If the heater element is burned, dryer does not heat or over heats, or clothes take too long to dry, then replacing this part could solve your problem. The tools needed for this repair project are: Phillips screwdriver, putty knife, needle nose pliers. To repair, first remove the main top of dryer and remove ground strap at the rear. Next, disconnect two wire harnesses that hold front panel to the cabinet to pull out front panel. Once you have access to the inside of the dryer, refer to the manual for further installation instruction. As a safety precaution, remember to unplug appliance from power source before beginning this repair project.

Dual Element Control Switch

40 Reviews

Part Number: WPW10434452

This switch controls the stove top surface burner.

Range Inner Door Glass

52 Reviews

Part Number: WP9781593

This genuine OEM part is the interior oven door glass that is the innermost heat barrier in your oven when the oven door is closed. The oven door glass measures approximately 18 1/4” x 12 3/4”. If the interior glass is broken or cracked, it can allow hot air to escape the oven cavity and should be replaced.

Washing Machine Suspension Rod Kit

25 Reviews

Part Number: W10780048

Friction Sleeve

10 Reviews

Part Number: WP8268961

The friction sleeve helps to reduce friction between the door hinge and the door and to keep your door quiet when it opens and closes. This part is a little over an inch long and is black in color. It is sold individually.

Dryer Drum Support Roller

3 Reviews

Part Number: WPW10314173

This drum support roller is sold individually. Most dryers require two. The tri-rings are included. This is a drum support roller for a dryer. It is a genuine replacement part. This part is sold separately. Most dryers require two drum rollers. It is recommended to check and replace both drum support rollers at the same time to ensure proper drum rotation and because they often wear at the same rate. The drum support roller holds the drum in the proper position while it spins on the support wheels. If rollers are worn out, they will cause the dryer to be noisy.