Hello!

You're visiting the Easy Appliance Parts site in Canada.

Would you like to shop on the U.S. site?

Go to U.S. site
Stay on this site

1107090799 Kenmore Dryer Parts List

1-15 of 199

Dryer drum support roller (support)

The drum support roller has a metallic bearing in its center. This part is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. If your dryer is noisy, won’t tumble or takes too long to dry, you might need to replace the roller. It is recommended that you replace both rollers at once. This is a genuine OEM part and is sold individually. Please remember to shut off the power to the dryer before starting the repair.

Easy Part #:

EAP11752609

Availability:

In Stock

Price:

$26.06

Idler pulley

A dryer's idler pulley helps the belt to rotate the drum. It is also known as dryer belt tension pulley wheel.

Easy Part #:

EAP334244

Availability:

In Stock

Price:

$30.95

Door catch kit (door latch kit)

This door catch kit contains two door strikes and three door catches to service dryer doors that have one or two catches. Make sure to read the instructions to determine which one to use for your model. These parts keep the dryer door closed to allow the dryer to operate. If your door won't stay closed or will not start you may need to replace this part. This is a genuine OEM part.

Easy Part #:

EAP334230

Availability:

In Stock

Price:

$4.95

Lint filter (lint screen)

This filter collects lint as it passes through the dryer vent.

Easy Part #:

EAP1491676

Availability:

In Stock

Price:

$70.60

Drive belt (dryer drum drive belt, 93 1/2 inches long, 4 ribs 3 grooves.)

This dryer drum belt has 4 ribs and 3 grooves. This belt is 1/4 of an inch wide. This drive belt is 93 1/2 inches long, and 1/4 of an inch wide, with 4 ribs and 3 grooves. To complete this repair, you will need a Phillips screw driver, a 1/4 inch nut driver, a putty knife, and a pair of needle nose pliers. Make sure to disconnect power to the dryer before beginning this repair.

Easy Part #:

EAP11722115

Availability:

In Stock

Price:

$25.21

M series new style coil kit (dryer gas burner valve solenoid set. If the dryer does not heat or heats intermittently the coils could be defective.)

This gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two-terminal secondary coil. If there is no heat or your drying time is getting longer, the coils may be bad and will need to be replaced. Once the coils go bad they do not hold the gas valve open properly. Usually only one of them burns out but you should replace them as a set. Both must be operational for the gas valve to open. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Easy Part #:

EAP334310

Availability:

In Stock

Price:

$35.48

Leveling foot (leveling feet)

The adjustable leveling leg is used to support and keep your dryer level. It also allows you to adjust the height of your dryer. You may need to replace the leveling leg if one becomes lost, the thread is stripped off, or it is noisy during operation. The leveling leg is almost 2” long, white in color, and made of plastic. There are four leveling legs used on the dryer, please order quantity needed as they are sold individually. This is a genuine OEM part.

Easy Part #:

EAP1609293

Availability:

In Stock

Price:

$9.27

Roller support tri-ring (ring)

The tri ring is used to hold the drum support rollers or the idler pulley onto the shaft. If your dryer will not tumble or is noisy, you may need to replace the tri ring. This is a genuine OEM part and is sold individually.

Easy Part #:

EAP11755850

Availability:

In Stock

Price:

$15.41

Idler pulley with bracket (dryer idler pulley assembly.)

The idler pulley wheel is now sold with this arm. This idler pulley is for dryers. Idler pulley maintains correct tension on the drive belt to spin the drum.

Easy Part #:

EAP11726337

Availability:

In Stock

Price:

$30.77

Dryer drum seal with adhesive (seal)

This part seals the drum to prevents air from escaping. This includes silicone rubber adhesive.

Easy Part #:

EAP970088

Availability:

In Stock

Price:

$54.30

Moisture sensor (dryer moisture sensor bar. This moisture sensor monitors the clothing’s moisture level and sends a signal to the control board when the clothes are dr)

This is the moisture sensor for your dryer. It helps detect the amount of moisture in your clothes during the dryer cycle. If you notice your clothes are still wet after an automatic dryer cycle is done, you may need to replace the sensor. You will find the moisture sensor behind the lint screen. Be sure to disconnect the power source from the dryer before you begin this repair. Note: Some model's require two sensors, please order quantity needed. Sensor only, harness is not included. This part is sold individually.

Easy Part #:

EAP11741408

Availability:

In Stock

Price:

$11.97

Light bulb - 10w (light bulb)

This ten watt appliance light bulb is two inches tall. It is used with both washers and dryers.

Easy Part #:

EAP11739347

Availability:

In Stock

Price:

$18.75

Touch-up paint - white (tuchup)

This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, and freezers. This is a genuine OEM part and includes a brush applicator. Please remember to wear gloves to protect your hands when applying this paint.

Easy Part #:

EAP385132

Availability:

In Stock

Price:

$8.72

Blower wheel

The blower wheel pulls air over the heat source, through the clothes drum, and past the thermostats, then pushes it out the exhaust duct. The blower wheel, which is usually plastic, may wear out over time. But if it's noisy, it may simply be clogged with lint. Clean the blower and test to see if the dryer is still noisy. If it is, you probably need to replace it.

Easy Part #:

EAP11743811

Availability:

In Stock

Price:

$93.18

Dryer radiant flame sensor (radiant sensor)

This part senses if the igniter is hot enough to ignite the flame for heat, allowing the gas valve to open. The sensor is three inches long and is used for many gas clothes dryers. If your dryer is not creating any heat, taking too long to dry or shuts off too soon, you may need to replace the flame sensor. This is a genuine OEM part and is made of both plastic and metal. Please remember to disconnect power to your dryer before starting your repair.

Easy Part #:

EAP11741429

Availability:

In Stock

Price:

$55.03

1-15 of 199