Hello!

You're visiting the Easy Appliance Parts site in Canada.

Would you like to shop on the U.S. site?

Go to U.S. site
Stay on this site

110798328 Kenmore Dryer Parts List

1-15 of 169

Dryer thermal fuse (non-resettable thermal fuse)

This thermal fuse is used in dryers as a safety mechanism that stops the flow of electricity to the motor circuit when a dryer overheats. This replacement part features two 3/16 inch terminals, and is sold individually. When this fuse is faulty, your dryer will not start or it will not heat properly. This is a one-time fuse, meaning it cannot be re-set. It must be replaced when there is no longer continuity between the terminals. It attaches to the blower wheel housing. Blown fuses can be caused by clogged dryer vents. We recommend checking to make sure all of the vents are clear when you perform this repair.

Easy Part #:

EAP11741460

Availability:

In Stock - Ships Today

Price:

$22.55

Dryer drum support roller (support)

The drum support roller has a metallic bearing in its center. This part is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. If your dryer is noisy, won’t tumble or takes too long to dry, you might need to replace the roller. It is recommended that you replace both rollers at once. This is a genuine OEM part and is sold individually. Please remember to shut off the power to the dryer before starting the repair.

Easy Part #:

EAP11752609

Availability:

In Stock - Ships Today

Price:

$26.06

Dryer repair kit (dryer repair kit, includes drum belt, 4 rollers and idler pulley, for 27" wide dryers built 1965 and later and thin twins.)

This dryer repair kit consists of five commonly replaced dryer parts: one multi-rib belt (part #661570V and measures 93 1/2 inches long), four drum support rollers, one idler assembly, nine tri-rings, and one washer. This universal maintenance kit is an all-encompassing kit for fixing a noisy dryer, among other symptoms, but noisy being the most common. It is compatible with 27-inch wide dryers built from 1965 onwards. Be sure to disconnect the dryer or shut off the house circuit breaker for the appliance before you begin your repair. To access these parts, you will need to remove the dryer drum. For this installation you will need a 1/4-inch nut driver, a long flat-blade screwdriver, a short flat-blade screw diver, and a Phillips screwdriver.

Easy Part #:

EAP373088

Availability:

In Stock - Ships Today

Price:

$61.55

Idler pulley

A dryer's idler pulley helps the belt to rotate the drum. It is also known as dryer belt tension pulley wheel.

Easy Part #:

EAP334244

Availability:

In Stock - Ships Today

Price:

$30.95

Door catch kit (door latch kit)

This door catch kit contains two door strikes and three door catches to service dryer doors that have one or two catches. Make sure to read the instructions to determine which one to use for your model. These parts keep the dryer door closed to allow the dryer to operate. If your door won't stay closed or will not start you may need to replace this part. This is a genuine OEM part.

Easy Part #:

EAP334230

Availability:

In Stock - Ships Today

Price:

$4.95

Easy Part #:

EAP1491676

Availability:

In Stock - Ships Today

Price:

$70.60

Drive belt

This dryer drum belt has 4 ribs and 3 grooves. This belt is 1/4 of an inch wide. This drive belt is 93 1/2 inches long, and 1/4 of an inch wide, with 4 ribs and 3 grooves. To complete this repair, you will need a Phillips screw driver, a 1/4 inch nut driver, a putty knife, and a pair of needle nose pliers. Make sure to disconnect power to the dryer before beginning this repair.

Easy Part #:

EAP11722115

Availability:

In Stock - Ships Today

Price:

$25.21

M series new style coil kit (dryer gas burner valve solenoid set. If the dryer does not heat or heats intermittently the coils could be defective.)

This gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two-terminal secondary coil. If there is no heat or your drying time is getting longer, the coils may be bad and will need to be replaced. Once the coils go bad they do not hold the gas valve open properly. Usually only one of them burns out but you should replace them as a set. Both must be operational for the gas valve to open. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Easy Part #:

EAP334310

Availability:

In Stock - Ships Today

Price:

$35.48

Thermostat, internal-bias (thermistor)

This thermostat may differ in appearance, but functions the same as the original part. This part controls the temperature of the inside of the dryer drum and prevents the dryer from overheating.

Easy Part #:

EAP11746740

Availability:

In Stock - Ships Today

Price:

$54.83

Dryer door switch (door switch)

This 3-wire with leads dryer door switch is an on and off mechanism that prevents the dryer from operating while the door is open. The dryer will not operate until the door switch signals that the dryer door is closed. If the dryer won’t start, the lever broke off, or the switch shorted out, the appliance will not operate and the part will need to be replaced. This switch is a genuine OEM part and replaces the 2-wire switch. Please remember to disconnect the power to the dryer before starting the repair.

Easy Part #:

EAP11741701

Availability:

In Stock - Ships Today

Price:

$37.90

Leveling foot (leveling feet)

The adjustable leveling leg is used to support and keep your dryer level. It also allows you to adjust the height of your dryer. You may need to replace the leveling leg if one becomes lost, the thread is stripped off, or it is noisy during operation. The leveling leg is almost 2” long, white in color, and made of plastic. There are four leveling legs used on the dryer, please order quantity needed as they are sold individually. This is a genuine OEM part.

Easy Part #:

EAP1609293

Availability:

In Stock - Ships Today

Price:

$9.27

Roller support tri-ring (ring)

The tri ring is used to hold the drum support rollers or the idler pulley onto the shaft. If your dryer will not tumble or is noisy, you may need to replace the tri ring. This is a genuine OEM part and is sold individually.

Easy Part #:

EAP11755850

Availability:

In Stock - Ships Today

Price:

$15.41

Idler pulley with bracket (dryer idler pulley assembly.)

The idler pulley wheel is now sold with this arm. This idler pulley is for dryers. Idler pulley maintains correct tension on the drive belt to spin the drum.

Easy Part #:

EAP11726337

Availability:

In Stock - Ships Today

Price:

$30.77

Dryer drum seal with adhesive (seal)

This part seals the drum to prevents air from escaping. This includes silicone rubber adhesive.

Easy Part #:

EAP970088

Availability:

In Stock - Ships Today

Price:

$54.30

Moisture sensor (dryer moisture sensor bar. This moisture sensor monitors the clothing’s moisture level and sends a signal to the control board when the clothes are dr)

This is the moisture sensor for your dryer. It helps detect the amount of moisture in your clothes during the dryer cycle. If you notice your clothes are still wet after an automatic dryer cycle is done, you may need to replace the sensor. You will find the moisture sensor behind the lint screen. Be sure to disconnect the power source from the dryer before you begin this repair. Note: Some model's require two sensors, please order quantity needed. Sensor only, harness is not included. This part is sold individually.

Easy Part #:

EAP11741408

Availability:

In Stock - Ships Today

Price:

$11.97

1-15 of 169