41790802991 Kenmore Washer Dryer Combo Parts List

Search the entire 41790802991 by part description. Keep descriptions simple, e.g. "belt" or "pump". Need help?

Rear drum bearing kit (assembly-shaft (ballhitch))

This rear drum bearing kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws. The support bearing helps support the dryer drum to rotate quietly and smoothly during operation. The bearing attaches on the inside of the rear panel of the dryer cabinet. Over time the drum bearing will wear out. This kit will help keep your dryer running as smoothly as possible with as little noise as possible. This is a genuine OEM part. Please remember to disconnect the power before starting your repair.

Easy Part #:: EAP459829

Availability:: In Stock

Price:: $61.03

Upper drum glide (glide-drum)

The upper drum felt glide kit helps to support the front drum as it rotates smoothly and quietly while operating. This kit includes three glides with the adhesive. If your dryer won’t tumble or is noisy, the glide could be worn down causing you to hear a metal on metal noise and will need to be replaced. The drum glide is a genuine OEM part and sold individually. Please remember to disconnect the power to the dryer before starting your repair.

Easy Part #:: EAP470317

Availability:: In Stock

Price:: $39.97

Drum support bearing (bearing-drum support)

The rear drum support bearing helps support the dryer drum to rotate quietly and smoothly during operation. The bearing attaches on the inside of the rear panel of the dryer cabinet. If your dryer is making unusual noises or will not tumble, you may need to replace this part. It is white in color and made of plastic. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Easy Part #:: EAP418807

Availability:: In Stock

Price:: $7.06

Dryer lint screen (trap-lint)

This dryer lint screen is for laundry centers. Dryer lint screen captures lint and debris from the exhaust air flowing from the dryer. Follow the instructions in the owner's manual when installing this part.

Easy Part #:: EAP12585473

Availability:: In Stock

Price:: $95.53

Drive v-belt (belt-washer)

This drive belt is designed to ride on the pulley until the basket gets up to speed. If your washer drum won’t agitate or spin, you may need to replace your belt. It is recommended to disconnect the power to your washer and shut off the water supply before you start your repair. This drive belt is a genuine OEM part.

Easy Part #:: EAP1146950

Availability:: In Stock

Price:: $28.64

Door catch (catch-door)

The door catch helps keep the door closed while the machine is running. If your dryer will not start or the door will not close, you may need to replace the door catch. This is a genuine OEM part. Please remember to disconnect the power to your dryer before you start the repair.

Easy Part #:: EAP418433

Availability:: In Stock

Price:: $71.98

Front lower drum seal (seal-basket lower)

This part helps to keep the dryer running as quietly as possible.

Easy Part #:: EAP460194

Availability:: In Stock

Price:: $46.30

Thermal limiter - limit 220 (thermal limiter)

This thermal fuse limiter, with a limit of 220 degrees Fahrenheit, is manufactured for both gas and electric clothes dryers. Once the internal temperature of the dryer reaches 220 degrees, the heating element cuts out. If your dryer overheats, will not start, takes too long to dry, or has no heat or not enough heat, you will need to replace the fuse because it cannot be reset. This is a genuine OEM part. It is recommended to disconnect the power to your dryer before starting your repair.

Easy Part #:: EAP419402

Availability:: In Stock

Price:: $31.28

Screw (screw-front pnl, comb th ab, 10-16 x 0.500)

This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. The main reason you would replace this screw is if the old screw is missing or damaged. This part is sold individually and is an OEM part sourced directly from the manufacturer.

Easy Part #:: EAP417463

Availability:: In Stock

Price:: $14.85

Multi-rib drum belt (belt-dryer)

This belt helps rotate from the drive motor to the drum.

Easy Part #:: EAP3408299

Availability:: In Stock

Price:: $19.79

Tub seal assembly (seal-tub)

This tub seal helps prevent any leaking around the transmission of your washer. If your washer is leaking you may need to replace the seal. The tub seal is located on the bottom of the outer tub, in the center where the transmission comes through to connect to the agitator. This is a genuine OEM part. Please remember to shut off the water supply and disconnect the power to the washer before starting your repair.

Easy Part #:: EAP459481

Availability:: In Stock

Price:: $90.56

Door strike (strike-door)

The door strike works in conjunction with the dryer door. The male piece of the door strike is the piece that activates the door switch once the dryer door is closed. If your dryer won’t start, or the door won’t open/close, you may need to replace the door strike. This part is made from metal and measures approximately 1 inch. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting your repair.

Easy Part #:: EAP455020

Availability:: In Stock

Price:: $21.45

Start switch (switch-start)

This start switch is a manufacturer-approved replacement part for your dryer. A faulty start switch means your dryer will not begin its drying cycle. In order to complete this repair, you will need a Phillips screwdriver. Once you access the switch, disconnect the two wire leads and attach them to the new switch. Make sure to disconnect power to the unit before beginning this repair, and wear work gloves.

Easy Part #:: EAP1146154

Availability:: In Stock

Price:: $78.90

Heater assembly (heater-hsg assembly)

This dryer heating assembly has 5/16" terminal on the housing.

Easy Part #:: EAP2378363

Availability:: In Stock

Price:: $222.83

High limit thermostat (thermostat-safety)

The two-terminal high limit thermostat has a limit of 260 degrees Fahrenheit and acts as a safety mechanism that keeps the dryer from overheating. The thermostat will cut out when the internal dryer temperature reaches 260 and then cuts back in when the temperature drops by 70 degrees Fahrenheit. If your dryer is not heating, you may need to replace the thermostat. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting your repair.