Hello!

You're visiting the Easy Appliance Parts site in Canada.

Would you like to shop on the U.S. site?

Go to U.S. site
Stay on this site

41790862992 Kenmore Washer Dryer Combo Parts List

1-15 of 197

Rear drum bearing kit (asmy-shaft (ballhitch))

This rear drum bearing kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws. The support bearing helps support the dryer drum to rotate quietly and smoothly during operation. The bearing attaches on the inside of the rear panel of the dryer cabinet. Over time the drum bearing will wear out. This kit will help keep your dryer running as smoothly as possible with as little noise as possible. This is a genuine OEM part. Please remember to disconnect the power before starting your repair.

Easy Part #:

EAP459829

Availability:

In Stock

Price:

$61.03

Drain pump - 120v 60 hz. (pump-drain-wshr/lc-askoll)

The drain pump is what your washer uses to remove the water from the tub. The pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period. If your washer will not drain, is noisy, leaking, or has a burning smell, you may need to replace the drain pump. This pump has 120 volts, 60 hz and is a genuine OEM part. Please remember to shut off the water supply and disconnect the power to the washer before starting your repair. This part is the pump and motor assembly which includes the red flapper to prevent drain back flow.

Easy Part #:

EAP7783938

Availability:

In Stock

Price:

$190.17

Drum glide - white (glide-drum)

The white drum glide supports the drum on the front side and helps rotate smoothly and quietly while operating. If your dryer won’t tumble or is noisy, the drum glide may be worn down causing a metal on metal noise. Your dryer requires two glides; it is recommended to replace both glides at the same time. The drum glide is a genuine OEM part and is sold individually. Please remember to disconnect the power to the dryer before starting your repair.

Easy Part #:

EAP5574052

Availability:

In Stock

Price:

$40.35

Drum support bearing (bearing-drum support)

The rear drum support bearing helps support the dryer drum to rotate quietly and smoothly during operation. The bearing attaches on the inside of the rear panel of the dryer cabinet. If your dryer is making unusual noises or will not tumble, you may need to replace this part. It is white in color and made of plastic. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Easy Part #:

EAP418807

Availability:

In Stock

Price:

$7.06

Dryer lint screen (trap-lint)

This dryer lint screen is for laundry centers. Dryer lint screen captures lint and debris from the exhaust air flowing from the dryer. Follow the instructions in the owner's manual when installing this part.

Easy Part #:

EAP12585473

Availability:

In Stock

Price:

$95.53

Drive v-belt (belt-washer)

This drive belt is designed to ride on the pulley until the basket gets up to speed. If your washer drum won’t agitate or spin, you may need to replace your belt. It is recommended to disconnect the power to your washer and shut off the water supply before you start your repair. This drive belt is a genuine OEM part.

Easy Part #:

EAP1146950

Availability:

In Stock

Price:

$28.64

Door catch (catch-door)

The door catch helps keep the door closed while the machine is running. If your dryer will not start or the door will not close, you may need to replace the door catch. This is a genuine OEM part. Please remember to disconnect the power to your dryer before you start the repair.

Easy Part #:

EAP418433

Availability:

In Stock

Price:

$71.98

Front lower drum seal (seal-basket lower)

This part helps to keep the dryer running as quietly as possible.

Easy Part #:

EAP460194

Availability:

In Stock

Price:

$46.30

Screw (screw-front pnl,comb th ab ,10-16 x 0.500)

This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. The main reason you would replace this screw is if the old screw is missing or damaged. This part is sold individually and is an OEM part sourced directly from the manufacturer.

Easy Part #:

EAP417463

Availability:

In Stock

Price:

$14.85

Multi-rib drum belt (belt-dryer)

This belt helps rotate from the drive motor to the drum.

Easy Part #:

EAP3408299

Availability:

In Stock

Price:

$19.79

Tub seal assembly (seal-tub)

This tub seal helps prevent any leaking around the transmission of your washer. If your washer is leaking you may need to replace the seal. The tub seal is located on the bottom of the outer tub, in the center where the transmission comes through to connect to the agitator. This is a genuine OEM part. Please remember to shut off the water supply and disconnect the power to the washer before starting your repair.

Easy Part #:

EAP459481

Availability:

In Stock

Price:

$90.56

Door strike (strike-door)

The door strike works in conjunction with the dryer door. The male piece of the door strike is the piece that activates the door switch once the dryer door is closed. If your dryer won’t start, or the door won’t open/close, you may need to replace the door strike. This part is made from metal and measures approximately 1 inch. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting your repair.

Easy Part #:

EAP455020

Availability:

In Stock

Price:

$21.45

M series ignition coil kit (coil-secondary)

The gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two-terminal secondary coil. If it takes too long to dry or there is no heat, the coils may be bad and will need to be replaced. When the coils go bad they won’t hold the gas valve open properly. Usually only one of them burns out but you should replace them as a set. Both must be operational for the gas valve to open. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Easy Part #:

EAP470049

Availability:

In Stock

Price:

$31.28

Start switch (switch-start)

This start switch is a manufacturer-approved replacement part for your dryer. A faulty start switch means your dryer will not begin its drying cycle. In order to complete this repair, you will need a Phillips screwdriver. Once you access the switch, disconnect the two wire leads and attach them to the new switch. Make sure to disconnect power to the unit before beginning this repair, and wear work gloves.

Easy Part #:

EAP1146154

Availability:

In Stock

Price:

$78.90

Front upper felt seal with adhesive (felt-upper)

The upper felt seal for your dryer is attached to the top edge of the drum support area, and is held there by a high temperature adhesive. It creates a seal where the dryer door opens and closes, so that heat remains in the dryer while it tumbles. If your old upper felt seal is coming apart, you notice that hot air is leaking out the dryer door, or your clothes are taking too long to dry, you may need to replace the seal. When you order this part, it comes with the upper felt seal, as well as the required high-temperature adhesive.

Easy Part #:

EAP832644

Availability:

In Stock

Price:

$22.75

1-15 of 197