LG Dryer Parts

Washing Machine Drain Pump

24 Reviews

Part Number: 4681EA2001T

This drain pump motor helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period. If your washer will not drain, is noisy, leaking, or pumps but will not spin, you may need to replace the drain pump motor. This is a genuine OEM part. Please remember to shut off the water supply and disconnect the power to the washer before starting your repair. Note: Pump casing is not included.

Dryer Lint Filter

5 Reviews

Part Number: ADQ56656401

The Dryer's Lint Filter is used to collect lint during the dryer cycle as it passes through the dryer vent, in order to prevent damage to the machine. This manufacturer-approved part comes in gray, measures around 12 inches wide by 11 inches high, and is easy to install. It slides into the lint filter slot in your dryer. If there is visible damage to the screen then it's time to replace the part. We recommend that you thoroughly clean the lint filter before every load, but even with good maintenance, this hard-working part is often damaged or worn over time. If your dryer isn't drying quickly, the filter may be responsible. The manufacturer has made an authorized substitution to the lint filter. Special details: When replacing lint screen ADQ56656401 you may need to also replace lint screen housing MCK49049101 and lint screen guide MEA49050001 to prevent items from catching on the lint screen, depending on your model.

PARTS ASSEMBLY, SVC (2 Pack)

3 Reviews

Part Number: AGM75510755

The drum support roller for your dryer holds the drum in place while the drum turns on the support wheels. The drum roller is round with a bearing in the middle and measures approximately 3 inches in diameter. If the dryer is noisy, won’t tumble, or takes too long to dry, you might need to replace the support roller. It is recommended that you replace both rollers at once. The bearing inside this roller is self-lubricating, so no grease will be required. Please remember to disconnect the power to your appliance before starting your repair. This is a genuine OEM part.

Thermal Fuse

1 Review

Part Number: 6931EL3003D

The high limit thermostat protects the dryer by shutting off the heating element when the dryer overheats. If the thermostat has blown, dryer won’t start or there is no heat, the thermostat will need to be replaced it can not be reset. If your dryer vent is clogged it could cause the thermostat to blow as well. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting the repair.

Dryer Lint Filter

8 Reviews

Part Number: 5231EL1003B

The lint filter has a felt strip and is used to collect lint and debris as it passes through the dryer vent. It is recommended to clean the lint filter before every load. If your dryer takes too long to dry you may need to replace the filter. This is a genuine OEM part.

Dryer Lint Filter Assembly

2 Reviews

Part Number: 5231EL1001C

The lint filter sits in your dryer, and collects loose lint when the machine is operating. Sometimes the lint filter will become clogged or damaged, and in this case, you will need to replace your current lint filter with this part. The frame of this line filter is made of white plastic, and the filter is sold individually. To replace the filter, simply remove the old, damaged filter, and replace it with the new one.

Magnetic Door Plunger

Part Number: AGM73610701

The magnetic door plunger attaches to the inner door panel of your washer and will hold the door open when the washer is not in use and allows the door and tub seal to dry. By doing this it will prevent mold and mildew buildup around your door and seal. If your washer door will not close you many need to replace this part. The magnetic door plunger is a genuine OEM part.

Dryer Drum Belt

Part Number: 4400EL2001F

The drive belt is made to wrap around the drum, working with the tension pulley to rotate the drum. If your dryer drum won’t turn, then you may need to replace your belt. This drive belt is ¼” wide with 4 ribs and 3 grooves. It is recommended to disconnect the power to your dryer before you start your repair. This drive belt is a genuine OEM part.

Water Inlet Valve - Hot

2 Reviews

Part Number: 5220FR2006H

The hot water inlet valve is located on the back of the washer and it helps control the amount of water that enters into the washer. The valve has a standard hose fitting inlet, 1 water outlet, 120 volts and 6 watts. If the washer is filling slowly or not at all, the solenoid may have gone bad and you will need to replace the inlet valve. The valve measures approximately 3” L x 2 3/4” W. Please remember to disconnect the water and power to the washer before starting the repair. This is a genuine OEM hot water inlet valve.

Lint Filter

1 Review

Part Number: ADQ73373201