LG Parts

PARTS ASSEMBLY, SVC (2 Pack)

2 Reviews

Part Number: AGM75510755

The drum support roller for your dryer holds the drum in place while the drum turns on the support wheels. The drum roller is round with a bearing in the middle and measures approximately 3 inches in diameter. If the dryer is noisy, won’t tumble, or takes too long to dry, you might need to replace the support roller. It is recommended that you replace both rollers at once. The bearing inside this roller is self-lubricating, so no grease will be required. Please remember to disconnect the power to your appliance before starting your repair. This is a genuine OEM part.

Washing Machine Drain Pump

21 Reviews

Part Number: 4681EA2001T

This drain pump motor helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period. If your washer will not drain, is noisy, leaking, or pumps but will not spin, you may need to replace the drain pump motor. This is a genuine OEM part. Please remember to shut off the water supply and disconnect the power to the washer before starting your repair. Note: Pump casing is not included.

Refrigerator Door Switch

Part Number: 6600JB1010A

The light switch lights up the interior cabinet of the refrigerator or freezer when the door is opened. If you open the door and the light won’t come on, or the light is always on, you may need to replace the light switch. The switch is white in color and measures approximately 2 1/2”. This is a genuine OEM part. Please remember to disconnect the power before starting the repair.

Dryer Lint Filter

4 Reviews

Part Number: ADQ56656401

The Dryer's Lint Filter is used to collect lint during the dryer cycle as it passes through the dryer vent, in order to prevent damage to the machine. This manufacturer-approved part comes in gray, measures around 12 inches wide by 11 inches high, and is easy to install. It slides into the lint filter slot in your dryer. If there is visible damage to the screen then it's time to replace the part. We recommend that you thoroughly clean the lint filter before every load, but even with good maintenance, this hard-working part is often damaged or worn over time. If your dryer isn't drying quickly, the filter may be responsible. The manufacturer has made an authorized substitution to the lint filter. Special details: When replacing lint screen ADQ56656401 you may need to also replace lint screen housing MCK49049101 and lint screen guide MEA49050001 to prevent items from catching on the lint screen, depending on your model.

Door Stopper

4 Reviews

Part Number: 4620JJ2009A

Thermal Fuse

1 Review

Part Number: 6931EL3003D

The high limit thermostat protects the dryer by shutting off the heating element when the dryer overheats. If the thermostat has blown, dryer won’t start or there is no heat, the thermostat will need to be replaced it can not be reset. If your dryer vent is clogged it could cause the thermostat to blow as well. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting the repair.

Dryer Drum Belt

Part Number: 4400EL2001F

The drive belt is made to wrap around the drum, working with the tension pulley to rotate the drum. If your dryer drum won’t turn, then you may need to replace your belt. This drive belt is ¼” wide with 4 ribs and 3 grooves. It is recommended to disconnect the power to your dryer before you start your repair. This drive belt is a genuine OEM part.

Plastic Tube - 5/16 Inch

1 Review

Part Number: MJU62070602

The 5/16” plastic water tubing attaches to the water inlet valve and goes into the refrigerator. The tubing supplies water to the water dispenser and the ice maker. If the tubing becomes damaged or cracked, it can cause water to leak out onto the floor and the water tubing will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power and water supply before starting the repair.

Water Inlet Valve - Hot

2 Reviews

Part Number: 5220FR2006H

The hot water inlet valve is located on the back of the washer and it helps control the amount of water that enters into the washer. The valve has a standard hose fitting inlet, 1 water outlet, 120 volts and 6 watts. If the washer is filling slowly or not at all, the solenoid may have gone bad and you will need to replace the inlet valve. The valve measures approximately 3” L x 2 3/4” W. Please remember to disconnect the water and power to the washer before starting the repair. This is a genuine OEM hot water inlet valve.

Blower Thermostat

Part Number: 6931EL3002M

The blower housing exhaust thermostat works in conjunction with your dryer by helping to regulate the temperature inside of the dryer drum. The thermostat will turn the heat off and on to help maintain the required temperature in the drum. If your dryer is not heating the thermostat may have shorted out and will need to be replaced. This is a genuine OEM part. Please remember to shut the power off to the dryer before starting the repair.