Maytag Dryer Parts

Dryer Repair Kit

40 Reviews

Part Number: 4392067

This dryer repair kit consists of five commonly replaced dryer parts: one multi-rib belt (part #661570V and measures 93 1/2 inches long), four drum support rollers, one idler assembly, nine tri-rings, and one washer. This universal maintenance kit is an all-encompassing kit for fixing a noisy dryer, among other symptoms, but noisy being the most common. It is compatible with 27-inch wide dryers built from 1965 onwards. Be sure to disconnect the dryer or shut off the house circuit breaker for the appliance before you begin your repair. To access these parts, you will need to remove the dryer drum. For this installation you will need a 1/4-inch nut driver, a long flat-blade screwdriver, a short flat-blade screw diver, and a Phillips screwdriver.

Heating Element - 5300W

Part Number: DC47-00019A

Includes the insulators and restring already attached. This dryer heating element produces heat to dry clothes in a dryer and is located in the rear end. If the heater element is burned, dryer does not heat or over heats, or clothes take too long to dry, then replacing this part could solve your problem. The tools needed for this repair project are: Phillips screwdriver, putty knife, needle nose pliers. To repair, first remove the main top of dryer and remove ground strap at the rear. Next, disconnect two wire harnesses that hold front panel to the cabinet to pull out front panel. Once you have access to the inside of the dryer, refer to the manual for further installation instruction. As a safety precaution, remember to unplug appliance from power source before beginning this repair project.

Dryer Drum Support Roller

3 Reviews

Part Number: WPW10314173

This drum support roller is sold individually. Most dryers require two. The tri-rings are included. This is a drum support roller for a dryer. It is a genuine replacement part. This part is sold separately. Most dryers require two drum rollers. It is recommended to check and replace both drum support rollers at the same time to ensure proper drum rotation and because they often wear at the same rate. The drum support roller holds the drum in the proper position while it spins on the support wheels. If rollers are worn out, they will cause the dryer to be noisy.

Multi Rib Belt - 92-1/4"

66 Reviews

Part Number: 341241

This dryer drum belt has four ridges, three grooves, 1/4-inch wide and 92 1/4-inch long. The belt helps rotate the drum. If the drum does not rotate and you can still hear the motor running, the belt may have broken and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Idler Pulley with Bracket

15 Reviews

Part Number: W10837240

The idler pulley wheel is now sold with this arm. This idler pulley is for dryers. Idler pulley maintains correct tension on the drive belt to spin the drum.

Drum Support Roller Kit

10 Reviews

Part Number: 12001541

This drum support roller includes one drum roller and two washer bearings. The drum support roller holds the drum in place while the drum rotates on the support wheels. If the dryer is making a loud rumbling noise or will not tumble, you may need to replace the roller. Most dryers use two drum rollers, and it is recommended to change both at once. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting the repair.

Heating Element - 240V 5400W

19 Reviews

Part Number: 279838

This 240V/5400W heating element is strung with a coiled wire made of a nickel and a chrome alloy. This wire receives, but resists, a controlled electric current, causing the wire to heat up. The heat produced is used to dry the clothes in your dryer. If the dryer has no heat, takes too long to dry, or the heating element burns out, the heating element will need to be replaced since it cannot be repaired. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting your repair.

Dryer Thermal Fuse

45 Reviews

Part Number: WP3392519

This thermal fuse is used in dryers as a safety mechanism that stops the flow of electricity to the motor circuit when a dryer overheats. This replacement part features two 3/16 inch terminals, and is sold individually. When this fuse is faulty, your dryer will not start or it will not heat properly. This is a one-time fuse, meaning it cannot be re-set. It must be replaced when there is no longer continuity between the terminals. It attaches to the blower wheel housing. Blown fuses can be caused by clogged dryer vents. We recommend checking to make sure all of the vents are clear when you perform this repair.

Idler Pulley Assembly

Part Number: DC93-00634A

Tumbler and Motor Belt

10 Reviews

Part Number: WPY312959

The drum drive belt is made to wrap around the drum, slip on the tension pulley to rotate the drum. If your dryer drum won’t turn when in operation, the drum drive belt is probably broken and will need to be replaced. This drive belt is 3/8” wide 100” long with 5 ribs and 4 grooves. It is recommended to disconnect the power to your dryer before you start your repair. This drum drive belt is a genuine OEM part.