41003 LG Washer Parts List

Search the entire 41003 by part description. Keep descriptions simple, e.g. "belt" or "pump". Need help?

Washing machine drain pump (washing machine drain pump. If the washer does not drain then the drain pump may be clogged, damaged, or defective.)

This drain pump motor helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period. If your washer will not drain, is noisy, leaking, or pumps but will not spin, you may need to replace the drain pump motor. This is a genuine OEM part. Please remember to shut off the water supply and disconnect the power to the washer before starting your repair. Note: Pump casing is not included.

Easy Part #:: EAP3579318

Availability:: In Stock

Price:: $140.89

Water inlet valve - hot (washer hot water inlet valve. Standard hose fitting inlet, 1 water outlet. The water inlet valve opens to allow water to enter the washing machine.)

The hot water inlet valve is located on the back of the washer and it helps control the amount of water that enters into the washer. The valve has a standard hose fitting inlet, 1 water outlet, 120 volts and 6 watts. If the washer is filling slowly or not at all, the solenoid may have gone bad and you will need to replace the inlet valve. The valve measures approximately 3” L x 2 3/4” W. Please remember to disconnect the water and power to the washer before starting the repair. This is a genuine OEM hot water inlet valve.

Easy Part #:: EAP3527427

Availability:: In Stock

Price:: $68.41

Magnetic door plunger (washer door magnet holder kit)

The magnetic door plunger attaches to the inner door panel of your washer and will hold the door open when the washer is not in use and allows the door and tub seal to dry. By doing this it will prevent mold and mildew buildup around your door and seal. If your washer door will not close you many need to replace this part. The magnetic door plunger is a genuine OEM part.

Easy Part #:: EAP3618292

Availability:: In Stock

Price:: $68.78

Gasket

This part is the replacement rear tub gasket for your washer. It is made of black plastic and is approximately 3-1/4 inches in diameter. The rear tub gasket forms a watertight seal between the rear tub and the drive shaft. If the gasket is worn or damaged, it may not be able to create this seal, and you may experience a water leak from your washer. Be sure to disconnect the washer from the water and power sources before you begin this repair. This is an OEM part sourced directly from the manufacturer and it is sold individually.

Easy Part #:: EAP3535219

Availability:: In Stock

Price:: $35.36

Bearing,ball

Tub bearing. This part is very difficult to install. The manufacturer recommends replacing the complete rear tub and bearing assembly.

Easy Part #:: EAP3522899

Availability:: In Stock

Price:: $116.70

Shock absorber (shock absorber kit)

Easy Part #:: EAP3522317

Availability:: Special Order

Price:: $73.85

Tub-to-pump drain hose (washing machine drain hose with bellows. This drain hose makes a connection from the washer tub to the drain pump.)

This hose has bellows to allow for flexibility during the wash and spin cycles.

Easy Part #:: EAP3523345

Availability:: In Stock

Price:: $47.92

Cap,drain hose (drain hose cap)

This drain hose plug, also known as a hose cap, is a genuine OEM part for your washing machine. This plug caps the drain hose from the pump housing, and helps prevent leaks from your washer. Before beginning this repair, make sure the power and water sources to your washer are shut off. To access the pump housing, open the pump filter cover, pull out the drain hose, remove the old plug and replace it, first draining the remaining water from the drain hose.

Easy Part #:: EAP3635866

Availability:: In Stock

Price:: $9.23

Detergent dispenser (box assembly, liquid detergent)

The blue plastic detergent dispenser holds the detergent and then dispenses it into the washer during the wash cycle. If the detergent dispenser is broken, lost, or if the detergent is not dispensed during the wash cycle, you may need to replace it. The dispenser is approximately 4”wide, 4.5” long, 2” tall and is an genuine OEM part.

Easy Part #:: EAP3522644

Availability:: In Stock

Price:: $32.27

Hose assembly,drain

Easy Part #:: EAP3527325

Availability:: In Stock

Price:: $79.63

Leg assembly

This levelling leg is a genuine replacement part. It is used to help keep your washing machine stable and balanced. It helps support your appliance. It screws into the base of your washer, and you can thread it in or out to adjust the height. The foot on this leg is made of rubber, which helps with grip, stabilization, and vibration reduction. It is also hexagonal in shape, which allows you to more easily adjust it. This levelling leg features a locknut on the shaft which can be tightened against the bottom of your appliance, this will stop the leg from rotating while you are using your washer. This replacement is sold individually.

Easy Part #:: EAP7788210

Availability:: In Stock

Price:: $45.05

Thermistor,ntc (thermistor temperature sensor. Works in conjunction with the main control board to monitor the water temperature.)

Easy Part #:: EAP3528953

Availability:: In Stock

Price:: $33.88

Pump filter (washing machine filter and trap assembly.)

This replacement pump filter, also known as a filter assembly, is a genuine OEM part for your washer or washer/dryer combo. Before beginning this repair, turn off the power and water supply to your washer. The filter assembly may need to be replaced because it is broken or is leaking water. To locate the filter assembly, pry open the small door on the front of the washer, using a flat-blade screwdriver. Unplug the drain hose next to the filter and drain the water into a bucket. Then unscrew the pump filter, and replace with your new one.

Easy Part #:: EAP3522306

Availability:: In Stock

Price:: $30.74

Hose,connector

This part is the replacement connector hose or clean-out drain hose for your washer. It is black in color and is sold individually. The connector hose drains water out of the washer if the drain cycle is not working. If the hose breaks, it will not be able to drain the water properly, and you may experience a water leak. Be sure to disconnect your washer from the power source, as well as the water source before you begin this repair. This is an OEM part sourced directly from the manufacturer.