Hello!

You're visiting the Easy Appliance Parts site in Canada.

Would you like to shop on the U.S. site?

Go to U.S. site
Stay on this site

48842 LG Parts List

1-15 of 101

Washing machine drain pump

This drain pump motor helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period. If your washer will not drain, is noisy, leaking, or pumps but will not spin, you may need to replace the drain pump motor. This is a genuine OEM part. Please remember to shut off the water supply and disconnect the power to the washer before starting your repair. Note: Pump casing is not included.

Easy Part #:

EAP3579318

Availability:

In Stock

Price:

$134.89

Water inlet valve - hot (washer hot water inlet valve. Standard hose fitting inlet, 1 water outlet. The water inlet valve opens to allow water to enter the washing machine.)

The hot water inlet valve is located on the back of the washer and it helps control the amount of water that enters into the washer. The valve has a standard hose fitting inlet, 1 water outlet, 120 volts and 6 watts. If the washer is filling slowly or not at all, the solenoid may have gone bad and you will need to replace the inlet valve. The valve measures approximately 3” L x 2 3/4” W. Please remember to disconnect the water and power to the washer before starting the repair. This is a genuine OEM hot water inlet valve.

Easy Part #:

EAP3527427

Availability:

In Stock

Price:

$65.34

Shock absorber kit

This kit includes 1 shock absorber and 2 pins.

Easy Part #:

EAP3522313

Availability:

In Stock

Price:

$57.95

Washer motor rotor position sensor (rotor position sensor (rps))

The sensor monitors the direction and speed of the spinning rotor.

Easy Part #:

EAP11706506

Availability:

In Stock

Price:

$36.41

Gasket (rear shaft seal at outer tub)

This genuine OEM drum seal gasket prevents water from leaking between the outer tub and spin basket of your washer. It is made of black rubber and measures 2.5 inches in diameter. If your washer is leaking, and running noisier than usual, check for wear on the gasket, and to ensure it is properly fitted.

Easy Part #:

EAP3522854

Availability:

In Stock

Price:

$37.05

Spider (rear flange (also called a spider) and shaft for washing machine drum. This part supports the dryer drum.)

The spider, or rear tub support, is located behind the outer tub of your washer, and provides support to the outer tub. It has 3 legs and each measures approximately 10 inches long. If your washer moves or shakes, or sounds noisier than usual during the washing cycle, the support spider may be faulty or broken and should be replaced immediately.

Easy Part #:

EAP12075847

Availability:

In Stock

Price:

$256.26

Pump casing

This part connects to the drain pump and motor.

Easy Part #:

EAP3518248

Availability:

In Stock

Price:

$32.75

Ball bearing (bearing,ball)

This bearing, or ball, is a genuine OEM replacement part for your washer. The bearing allows the tub to rotate smoothly. Replacing this part can be helpful if your washer is extremely loud, or vibrates excessively. Sometimes the seal can fail, allowing water to leak into the bearings. Often you will need to replace the inner and outer bearings, as well as the seal, at the same time.

Easy Part #:

EAP12072605

Availability:

In Stock

Price:

$56.67

Cap,drain hose (drain hose cap)

This drain hose plug, also known as a hose cap, is a genuine OEM part for your washing machine. This plug caps the drain hose from the pump housing, and helps prevent leaks from your washer. Before beginning this repair, make sure the power and water sources to your washer are shut off. To access the pump housing, open the pump filter cover, pull out the drain hose, remove the old plug and replace it, first draining the remaining water from the drain hose.

Easy Part #:

EAP3635866

Availability:

On Order

Price:

$8.76

Easy Part #:

EAP3522860

Availability:

In Stock

Price:

$31.82

Easy Part #:

EAP3527325

Availability:

In Stock

Price:

$76.08

Leg assembly

This levelling leg is a genuine replacement part. It is used to help keep your washing machine stable and balanced. It helps support your appliance. It screws into the base of your washer, and you can thread it in or out to adjust the height. The foot on this leg is made of rubber, which helps with grip, stabilization, and vibration reduction. It is also hexagonal in shape, which allows you to more easily adjust it. This levelling leg features a locknut on the shaft which can be tightened against the bottom of your appliance, this will stop the leg from rotating while you are using your washer. This replacement is sold individually.

Easy Part #:

EAP7788210

Availability:

In Stock

Price:

$15.85

Pump filter (washing machine filter and trap assembly.)

This replacement pump filter, also known as a filter assembly, is a genuine OEM part for your washer or washer/dryer combo. Before beginning this repair, turn off the power and water supply to your washer. The filter assembly may need to be replaced because it is broken or is leaking water. To locate the filter assembly, pry open the small door on the front of the washer, using a flat-blade screwdriver. Unplug the drain hose next to the filter and drain the water into a bucket. Then unscrew the pump filter, and replace with your new one.

Easy Part #:

EAP3522306

Availability:

In Stock

Price:

$30.74

Hose,connector

This part is the replacement connector hose or clean-out drain hose for your washer. It is black in color and is sold individually. The connector hose drains water out of the washer if the drain cycle is not working. If the hose breaks, it will not be able to drain the water properly, and you may experience a water leak. Be sure to disconnect your washer from the power source, as well as the water source before you begin this repair. This is an OEM part sourced directly from the manufacturer.

Easy Part #:

EAP3527289

Availability:

In Stock

Price:

$14.12

1-15 of 101