Kenmore Stove Parts

Terminal Block Kit

8 Reviews

Part Number: 5303935058

This surface burner terminal block kit comes with interchangeable mounting brackets, ceramic wire nuts, heat shrink protective tubing and wires. This part is used to connect the wire harness to the surface burner element. If your element will not heat at all, or is not heating properly, it is likely an issue with the terminal block and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power supply before starting your repair.

ELEMENT

3 Reviews

Part Number: 5304533520

Temperature Sensor

19 Reviews

Part Number: 316490000

This temperature sensor detects the temperature within the oven cavity.

Temperature Sensor

11 Reviews

Part Number: 316217002

The temperature sensor, also known as an oven probe, detects the temperature within the oven cavity. This temperature sensor is a genuine OEM part. If your oven is too hot, not heating evenly, has little to no heat when baking, or is flashing F3/F4 error messages on your control board, you may need to replace the temperature sensor. Please make sure to disconnect the power to your range before starting your repair.

Oven Sensor

2 Reviews

Part Number: WB21X5301

The temperature sensor, also known as an oven probe, detects the temperature within the oven cavity. This temperature sensor is a genuine OEM part. If your oven is too hot, not heating evenly, has little to no heat when baking, or is flashing F3/F4 error messages on your control board, you may need to replace it. Make sure to disconnect the power to your range before starting your repair.

Oven Bake Element

25 Reviews

Part Number: 318255006

The 3000W bake element is located on the bottom of the oven cavity to supply heat for baking. The element terminals are male quarter inch spade connectors and have push-on wire terminals. If your oven is not heating evenly, the element will not heat, or there is little to no heat when baking, you may need to replace the element. This genuine OEM bake element. Please remember to disconnect the power to your oven before you start your repair.

Light Bulb - 40W

18 Reviews

Part Number: 8009

This 40-watt light bulb has a standard screw-in base. It is used in many different appliances. If your current bulb is burnt out or broken you will need to replace it. This light bulb is a genuine OEM part and is sold individually.

Flat Style Oven Igniter Kit

23 Reviews

Part Number: 12400035

The flat style gas oven igniter is used to ignite the gas to light the oven burner, which produces heat for your range. If the element has shorted out, is no longer glowing, or is glowing but only orange or red rather than white, then you will need to replace the oven igniter. When replacing the igniter please be very careful not to touch the gray element part of the igniter as it is very fragile. The igniter measures approximately 3-3/4"in length and the amperage range is 3.3 to 3.6. This igniter kit can replace igniters for either the broil or bake burners and can replace shorter and longer igniters. The kit includes the igniter, 4 wire nuts, insulation, 2 wire assembly and a bracket. This is a genuine OEM part. Please make sure to disconnect the power and shut off the gas supply before starting your repair.

GLASS

11 Reviews

Part Number: 5304503232

This is also called the heat barrier glass.

Flat Style Oven Igniter

6 Reviews

Part Number: 5303935066

The flat-style oven igniter is used to ignite the gas to light the oven burner in your range. If your oven is not heating, check the igniter to make sure it is glowing. If the igniter is glowing and your oven is not heating, your igniter is not strong enough to heat the oven and you will need to replace it. When replacing the igniter, be very careful not to touch the black element part of the igniter as it is very fragile. The part measures approximately 3.72-inch in length and the amperage range is 3.2 to 3.6. This is a genuine OEM part.