Frigidaire Dryer Parts

Rear Drum Bearing Kit

23 Reviews

Part Number: 5303281153

This rear drum bearing kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws. The support bearing helps support the dryer drum to rotate quietly and smoothly during operation. The bearing attaches on the inside of the rear panel of the dryer cabinet. Over time the drum bearing will wear out. This kit will help keep your dryer running as smoothly as possible with as little noise as possible. This is a genuine OEM part. Please remember to disconnect the power before starting your repair.

Drum Belt

7 Reviews

Part Number: 134503600

This dryer drum belt is 88 3/4 inches long, and is 1/4 inch wide. The belt attaches to the motor pulley and helps rotate the drum as the motor rotates. If the drum does not rotate and you can still hear the motor running, the belt may have broken and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

USE WCI 215822000

Part Number: 131243700

Sold Individually.

Door Catch

3 Reviews

Part Number: 131658800

The door catch helps keep the door closed while the machine is running. If your dryer will not start or the door will not close, you may need to replace the door catch. This is a genuine OEM part. Please remember to disconnect the power to your dryer before you start the repair.

M Series Ignition Coil Kit

2 Reviews

Part Number: 5303931775

The gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two-terminal secondary coil. If it takes too long to dry or there is no heat, the coils may be bad and will need to be replaced. When the coils go bad they won’t hold the gas valve open properly. Usually only one of them burns out but you should replace them as a set. Both must be operational for the gas valve to open. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Upper Drum Glide

7 Reviews

Part Number: 5303937139

The upper drum felt glide kit helps to support the front drum as it rotates smoothly and quietly while operating. This kit includes three glides with the adhesive. If your dryer won’t tumble or is noisy, the glide could be worn down causing you to hear a metal on metal noise and will need to be replaced. The drum glide is a genuine OEM part and sold individually. Please remember to disconnect the power to the dryer before starting your repair.

Drum Support Bearing

2 Reviews

Part Number: 131825900

The rear drum support bearing helps support the dryer drum to rotate quietly and smoothly during operation. The bearing attaches on the inside of the rear panel of the dryer cabinet. If your dryer is making unusual noises or will not tumble, you may need to replace this part. It is white in color and made of plastic. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Door Strike

1 Review

Part Number: 5303207102

The door strike works in conjunction with the dryer door. The male piece of the door strike is the piece that activates the door switch once the dryer door is closed. If your dryer won’t start, or the door won’t open/close, you may need to replace the door strike. This part is made from metal and measures approximately 1 inch. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting your repair.

Heating Element Assembly

10 Reviews

Part Number: 131553900

This E-line assembly comes with a felt strip and insulators already attached. Heating elements are strung with a coiled wire made of a nickel and a chrome alloy. This wire receives, but resists, a controlled electric current and as a result, the wire heats up. The heat produced is used to dry the clothes in your dryer. If your dryer has little or no heat you may need to replace the heating element. This is a genuine OEM part. Please remember to shut off the power to the dryer before starting the repair.

Thermal Limiter - Limit 220

6 Reviews

Part Number: 134120900

This thermal fuse limiter, with a limit of 220 degrees Fahrenheit, is manufactured for both gas and electric clothes dryers. Once the internal temperature of the dryer reaches 220 degrees, the heating element cuts out. If your dryer overheats, will not start, takes too long to dry, or has no heat or not enough heat, you will need to replace the fuse because it cannot be reset. This is a genuine OEM part. It is recommended to disconnect the power to your dryer before starting your repair.