Kenmore Dryer Parts

Dryer Repair Kit

40 Reviews

Part Number: 4392067

This dryer repair kit consists of five commonly replaced dryer parts: one multi-rib belt (part #661570V and measures 93 1/2 inches long), four drum support rollers, one idler assembly, nine tri-rings, and one washer. This universal maintenance kit is an all-encompassing kit for fixing a noisy dryer, among other symptoms, but noisy being the most common. It is compatible with 27-inch wide dryers built from 1965 onwards. Be sure to disconnect the dryer or shut off the house circuit breaker for the appliance before you begin your repair. To access these parts, you will need to remove the dryer drum. For this installation you will need a 1/4-inch nut driver, a long flat-blade screwdriver, a short flat-blade screw diver, and a Phillips screwdriver.

Heating Element - 5300W

Part Number: DC47-00019A

Includes the insulators and restring already attached. This dryer heating element produces heat to dry clothes in a dryer and is located in the rear end. If the heater element is burned, dryer does not heat or over heats, or clothes take too long to dry, then replacing this part could solve your problem. The tools needed for this repair project are: Phillips screwdriver, putty knife, needle nose pliers. To repair, first remove the main top of dryer and remove ground strap at the rear. Next, disconnect two wire harnesses that hold front panel to the cabinet to pull out front panel. Once you have access to the inside of the dryer, refer to the manual for further installation instruction. As a safety precaution, remember to unplug appliance from power source before beginning this repair project.

Dryer Drum Support Roller

3 Reviews

Part Number: WPW10314173

This drum support roller is sold individually. Most dryers require two. The tri-rings are included. This is a drum support roller for a dryer. It is a genuine replacement part. This part is sold separately. Most dryers require two drum rollers. It is recommended to check and replace both drum support rollers at the same time to ensure proper drum rotation and because they often wear at the same rate. The drum support roller holds the drum in the proper position while it spins on the support wheels. If rollers are worn out, they will cause the dryer to be noisy.

Multi Rib Belt - 92-1/4"

66 Reviews

Part Number: 341241

This dryer drum belt has four ridges, three grooves, 1/4-inch wide and 92 1/4-inch long. The belt helps rotate the drum. If the drum does not rotate and you can still hear the motor running, the belt may have broken and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Drum Support Roller & Axle

Part Number: DC97-16782A

Sold individually.

Drum Bearing Slide - Green (Sold individually)

2 Reviews

Part Number: WE1M1067

This single green drum bearing slide attaches to the outer-most sides of the bearing to help support the front of the drum as it rotates. If your dryer is making loud noises or the drum won?t tumble you many need to replace the slides. The manufacturer recommends replacing both slides at the same time. There are 2 slides per dryer. This is a genuine OEM part. Please make sure to disconnect the power to the dryer before starting your repair.

Idler Pulley with Bracket

15 Reviews

Part Number: W10837240

The idler pulley wheel is now sold with this arm. This idler pulley is for dryers. Idler pulley maintains correct tension on the drive belt to spin the drum.

Upper Drum Glide

8 Reviews

Part Number: 5303937139

The upper drum felt glide kit helps to support the front drum as it rotates smoothly and quietly while operating. This kit includes three glides with the adhesive. If your dryer won’t tumble or is noisy, the glide could be worn down causing you to hear a metal on metal noise and will need to be replaced. The drum glide is a genuine OEM part and sold individually. Please remember to disconnect the power to the dryer before starting your repair.

Rear Drum Bearing Kit

24 Reviews

Part Number: 5303281153

This rear drum bearing kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws. The support bearing helps support the dryer drum to rotate quietly and smoothly during operation. The bearing attaches on the inside of the rear panel of the dryer cabinet. Over time the drum bearing will wear out. This kit will help keep your dryer running as smoothly as possible with as little noise as possible. This is a genuine OEM part. Please remember to disconnect the power before starting your repair.

Dryer Thermal Fuse

45 Reviews

Part Number: WP3392519

This thermal fuse is used in dryers as a safety mechanism that stops the flow of electricity to the motor circuit when a dryer overheats. This replacement part features two 3/16 inch terminals, and is sold individually. When this fuse is faulty, your dryer will not start or it will not heat properly. This is a one-time fuse, meaning it cannot be re-set. It must be replaced when there is no longer continuity between the terminals. It attaches to the blower wheel housing. Blown fuses can be caused by clogged dryer vents. We recommend checking to make sure all of the vents are clear when you perform this repair.