1107080299 Kenmore Dryer Parts List

Search the entire 1107080299 by part description. Keep descriptions simple, e.g. "belt" or "pump". Need help?

Dryer radiant flame sensor (radiant sensor)

This part senses if the igniter is hot enough to ignite the flame for heat, allowing the gas valve to open. The sensor is three inches long and is used for many gas clothes dryers. If your dryer is not creating any heat, taking too long to dry or shuts off too soon, you may need to replace the flame sensor. This is a genuine OEM part and is made of both plastic and metal. Please remember to disconnect power to your dryer before starting your repair.

Easy Part #:: EAP11741429

Availability:: In Stock

Price:: $55.03

Igniter kit (glow bar igniter)

This silicon carbide igniter with ceramic holder kit includes the 3-inch flat igniter, mounting bracket, 4-inch wire leads, and the plug. It can replace both round and flat igniters. This kit is used for many gas clothes dryers. This part ignites the gas within the dryer to heat the dryer during the cycle, so if your dryer takes too long to dry, has no heat or not enough heat, you may need to replace the igniter. Be sure to disconnect the power source from your dryer before you do this repair. The igniter is very fragile and should be handled with care.

Easy Part #:: EAP334180

Availability:: In Stock

Price:: $46.56

Lint filter (lint screen)

The lint filter with handle is used to collect lint and debris as it passes through the dryer vent. It is recommended to clean the lint filter before every load. If your dryer takes too long to dry you may need to replace the filter. This lint filter includes a white handle and measures approximately 23 inches including the handle. This is a genuine OEM part.

Easy Part #:: EAP16744854

Availability:: In Stock

Price:: $55.62

Dryer blower wheel (blower fan wheel)

The blower wheel is a squirrel cage type wheel whose purpose is to move the air through the room or appliance. The blower wheel spins on the motor shaft to blow air through the dryer drum and out through the exhaust.

Easy Part #:: EAP11743785

Availability:: In Stock

Price:: $42.08

Two-piece split ring bearing (support bearings)

This is a replacement bearing ring kit for your dryer. The bearing rings are found on the top and bottom lips of the dryer drum. If your dryer is unusually noisy, or the drum will not turn during operation, or if there are marks left on your clothes after a cycle, you may need to replace the bearing ring kit. The kit comes with 2 bearings, one for the top and one for the bottom of the dryer drum. Remove the front panel of your dryer to access the dryer drum for this repair. At this point you can use a pair of needle nose pliers to release the old bearing rings from the drum. Snap the new bearing rings on, and reassemble the dryer to complete your repair.

Easy Part #:: EAP334199

Availability:: In Stock

Price:: $67.45

Cover screw (screw)

Sold individually.

Easy Part #:: EAP11740701

Availability:: In Stock

Price:: $9.13

Lint trap housing seal (seal)

This seal comes with the adhesive backing.

Easy Part #:: EAP11741506

Availability:: In Stock

Price:: $11.22

Motor pulley - 60 hz. (motor pulley)

Sold individually.

Easy Part #:: EAP11744884

Availability:: In Stock

Price:: $60.79

Seal and bearing (bearing seal)

This front panel seal kit doesn't include the plastic retainers, reuse the old retainers. No glue is needed, the seal stretches to fit.

Easy Part #:: EAP11773177

Availability:: In Stock

Price:: $79.65

Temperature selector switch (switch)

This switch allows you to change the cycle settings on your dryer.

Easy Part #:: EAP11741508

Availability:: In Stock

Price:: $77.53

Leveling leg locking nut (nut)

This nut is sold individually. Size: 3/8-16

Easy Part #:: EAP11741219

Availability:: In Stock

Price:: $8.91

Seal

This seal comes with the adhesive backing.

Easy Part #:: EAP12745423

Availability:: In Stock

Price:: $20.59

Single front panel cip (clip)

This part is the replacement single front panel clip for your dryer. It is made of metal and is approximately 2 inches long and ¾ inch wide. The front panel retainer clip is what holds the front panel on to the dryer. If the clip is damaged or missing, or if the front panel appears loose, you may need to replace the clip. This part is sold individually and is an authentic OEM part.

Easy Part #:: EAP11731288

Availability:: In Stock

Price:: $18.91

Screw, 8/18 x 3/8 (screw 8pk)

This screw is sold individually.

Easy Part #:: EAP11746840

Availability:: In Stock

Price:: $6.22

Drum roller shaft - left side (shaft)

Replace the shaft of your left side drum support roller with this part from Whirlpool/Kenmore. This replacement shaft is 2-7/8 inches long. It is meant for use with many of Whirlpool/Kenmore's gas and electric clothes dryers that have been manufactured since 1965. Also known as Drum Roller Shaft.