110C96562500 Kenmore Dryer Parts List

Search the entire 110C96562500 by part description. Keep descriptions simple, e.g. "belt" or "pump". Need help?

Blower wheel

The blower wheel pulls air over the heat source, through the clothes drum, and past the thermostats, then pushes it out the exhaust duct. The blower wheel, which is usually plastic, may wear out over time. But if it's noisy, it may simply be clogged with lint. Clean the blower and test to see if the dryer is still noisy. If it is, you probably need to replace it.

Easy Part #:: EAP11743811

Availability:: In Stock

Price:: $81.58

Stacking kit

This kit allows you to stack your washer and dryer to maximize your laundry space.

Easy Part #:: EAP990537

Availability:: In Stock

Price:: $55.35

Dryer radiant flame sensor (gas dryer sensor for igniter and flame. The sensor is located across from the gas igniter at the dryer’s burner assembly.)

This part senses if the igniter is hot enough to ignite the flame for heat, allowing the gas valve to open. The sensor is three inches long and is used for many gas clothes dryers. If your dryer is not creating any heat, taking too long to dry or shuts off too soon, you may need to replace the flame sensor. This is a genuine OEM part and is made of both plastic and metal. Please remember to disconnect power to your dryer before starting your repair.

Easy Part #:: EAP11741429

Availability:: In Stock

Price:: $55.03

Igniter kit (dryer igniter kit. This igniter will replace both round and flat style igniters. The kit includes the bracket, wire nuts and mounting screw.)

This silicon carbide igniter with ceramic holder kit includes the 3-inch flat igniter, mounting bracket, 4-inch wire leads, and the plug. It can replace both round and flat igniters. This kit is used for many gas clothes dryers. This part ignites the gas within the dryer to heat the dryer during the cycle, so if your dryer takes too long to dry, has no heat or not enough heat, you may need to replace the igniter. Be sure to disconnect the power source from your dryer before you do this repair. The igniter is very fragile and should be handled with care.

Easy Part #:: EAP334180

Availability:: In Stock

Price:: $46.56

Drum support shaft - rear shaft with right hand threads (rear,left hand thread shaft. Part is updated so nuts may need to be replaced as well on older dryers.)

Shaft for dryer drum support roller. Rear shaft with left hand threads. Part is updated so nuts may need to be replaced as well on older dryers.

Easy Part #:: EAP11753708

Availability:: In Stock

Price:: $60.57

Cover screw (screw)

Sold individually.

Easy Part #:: EAP11740701

Availability:: In Stock

Price:: $9.13

Electronic control board (main control board. Note: This part is often misdiagnosed. Please enter your dryer model# in our repair help section for additonal repair help.)

This part is located in the control panel. It senses the resistance change and opens and closes a relay sending power to the dryer heater.

Easy Part #:: EAP11748354

Availability:: Special Order

Price:: $465.71

Motor pulley

This part is the replacement motor pulley for your dryer. The motor pulley allows the dryer belt to run straight while the dryer is operating. If your motor pulley is damaged, your dryer may not tumble, and may not start altogether. A damaged motor pulley can also damage the dryer belt, and it may need to be replaced as well. Be sure to disconnect power from the dryer before you begin this repair. This motor pulley is a genuine OEM part sourced directly from the manufacturer.

Easy Part #:: EAP11727942

Availability:: In Stock

Price:: $75.65

Thrust washer (washer. Has a 3/4-inch outside diameter.)

This part is located between the drum support rollers and idler pulley in your dryer to help prevent the parts from bumping up against the brackets they are attached to. If your dryer has a burning smell, is noisy, or will not tumble, you may need to replace the thrust washer. The washer is 3/4 inches in diameter and a is genuine OEM part. It is recommended to disconnect the power to your dryer before you start your repair.

Easy Part #:: EAP11740482

Availability:: In Stock

Price:: $9.13

Leveling leg locking nut (locking nut for leveling leg)

This nut is sold individually. Size: 3/8-16

Easy Part #:: EAP11741219

Availability:: In Stock

Price:: $8.91

Drive motor with threaded shaft - 120v 60hz (dryer drive motor. The drive motor drives the rotation of the dryer's drum. If the drive motor is defective, the dryer won't spin..)

The blower shaft is 1-5/8 inches long, while the drive shaft is 1-1/4 inches long.

Easy Part #:: EAP334287

Availability:: In Stock

Price:: $235.76

Screw - 10-16 x 1 (screw)

This screw is sold individually.

Easy Part #:: EAP11741409

Availability:: In Stock

Price:: $9.13

Lp gas con (dryer l.P conversion kit natural gas to lp (liquid propane). This kit includes the orifice, leak limiter, and instruction sheet.)

This gas conversion kit is used to convert natural gas burners to liquid propane in dryers. If your dryer will not start, heat, or there is an unusual smell, replacing this part can be a solution to the problem. The tools needed for this repair project are: a putty knife, 5/16 inch nut driver, small flathead screwdriver, pliers, and a 3/8 inch wrench. As a safety precaution remember to unplug your dryer from the power source before beginning this installation project. Refer to the manual provided by the manufacturer for further installation instructions and a detailed diagram.