41799680410 Kenmore Washer Dryer Combo Parts List

Search the entire 41799680410 by part description. Keep descriptions simple, e.g. "belt" or "pump". Need help?

Start switch (switch-start)

This start switch is a manufacturer-approved replacement part for your dryer. A faulty start switch means your dryer will not begin its drying cycle. In order to complete this repair, you will need a Phillips screwdriver. Once you access the switch, disconnect the two wire leads and attach them to the new switch. Make sure to disconnect power to the unit before beginning this repair, and wear work gloves.

Easy Part #:: EAP1146154

Availability:: In Stock

Price:: $79.09

Heater assembly (heater-hsg assembly)

This dryer heating assembly has 5/16" terminal on the housing.

Easy Part #:: EAP2378363

Availability:: In Stock

Price:: $223.42

High limit thermostat (thermostat-safety)

The two-terminal high limit thermostat has a limit of 260 degrees Fahrenheit and acts as a safety mechanism that keeps the dryer from overheating. The thermostat will cut out when the internal dryer temperature reaches 260 and then cuts back in when the temperature drops by 70 degrees Fahrenheit. If your dryer is not heating, you may need to replace the thermostat. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting your repair.

Easy Part #:: EAP446428

Availability:: In Stock

Price:: $107.34

Water inlet valve (valve-water)

This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed. If your washer will not stop filling with water, is leaking, or will not fill with water, you may need to replace the water inlet valve. Please make sure to disconnect the power to your washer before you start your repair. This water inlet valve is a genuine OEM part.

Easy Part #:: EAP815509

Availability:: In Stock

Price:: $72.90

Screw-in plastic leveling leg (leg-leveling, with pad)

Sold individually.

Easy Part #:: EAP1152204

Availability:: In Stock

Price:: $29.80

Agitator drive block (hub-drive)

The agitator drive block works in conjunction with the agitator in your washing machine by rotating the agitator assembly. If your washer is noisy and not agitating, you may need to replace the drive block because it may be worn out. This part is located between the agitator and the transmission shaft, measures approximately 2” long and is made of metal. This is a genuine OEM part. Please remember to disconnect the power and water supply before beginning your repair.

Easy Part #:: EAP1152574

Availability:: In Stock

Price:: $77.83

Drain hose (hose-drain 90")

This part comes with a ninety degree elbow.

Easy Part #:: EAP417877

Availability:: In Stock

Price:: $27.47

Spin bearing (bearing-outer tub)

The upper spin bearing works in conjunction with your washer. This part is located on the bottom of the outer tub where the transmission goes up through the middle of the tub. The spin bearing is used to support the transmission shaft in the drive system and allows the transmission shaft to be able to spin freely during the spin cycle. When the spin bearing goes bad it can cause noises during the spin cycle and will need to be replaced. This part is made of metal and is secured by mounting screws. The screws are not included, bearing only. This is a genuine OEM part. Please disconnect the water and power supply before starting the repair.

Easy Part #:: EAP446536

Availability:: In Stock

Price:: $97.67

Blower wheel (wheel-blower)

This blower wheel is a genuine OEM replacement part for your dryer. The wheel can become damaged through use of the dryer, especially if the drive motor shaft, which it is attached to, becomes damaged. This repair will require some disassembly of the dryer. Make sure to disconnect the power source and wear appropriate work gloves while conducting this repair.

Easy Part #:: EAP417911

Availability:: In Stock

Price:: $76.69

Dryer drum bearing bracket (bracker-bearing)

This drum bearing bracket is for dryers. Drum bearing bracket holds and supports the drum bearing

Easy Part #:: EAP12579101

Availability:: In Stock

Price:: $14.11

Tension idler pulley (arm-idler)

This idler arm assembly comes with the pulley wheel.

Easy Part #:: EAP418897

Availability:: No Longer Available

Screw (screw-shaft and baffle, comb ph ab spcl, 10-16 x .375)

Sold individually.

Easy Part #:: EAP417085

Availability:: In Stock

Price:: $15.62

Upper spin bearing washer (washer, spin bearing, upper)

The upper spin bearing washer works in conjunction with the spin bearing inside your washer. This part sits below the spin bearing. When the spin bearing washer becomes damaged there will be a metal on metal sound meaning it should be replaced. The washer measures approximately 2” in diameter and is sold individually. This is a genuine OEM part. Please remember to disconnect the water and power supply to the washer before starting this repair.