110798328 Kenmore Dryer Parts List

Search the entire 110798328 by part description. Keep descriptions simple, e.g. "belt" or "pump". Need help?

Light bulb - 10w (10-watt lamp)

This ten watt appliance light bulb is two inches tall. It is used with both washers and dryers.

Easy Part #:: EAP11739347

Availability:: In Stock

Price:: $18.75

Outlet screen door grille (outlet screen cover)

Top cover for lint filter.

Easy Part #:: EAP12070617

Availability:: In Stock

Price:: $32.05

Touch-up paint - white (tuchup)

This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, and freezers. This is a genuine OEM part and includes a brush applicator. Please remember to wear gloves to protect your hands when applying this paint.

Easy Part #:: EAP385132

Availability:: In Stock

Price:: $9.19

Blower wheel

The blower wheel pulls air over the heat source, through the clothes drum, and past the thermostats, then pushes it out the exhaust duct. The blower wheel, which is usually plastic, may wear out over time. But if it's noisy, it may simply be clogged with lint. Clean the blower and test to see if the dryer is still noisy. If it is, you probably need to replace it.

Easy Part #:: EAP11743811

Availability:: In Stock

Price:: $81.58

Dryer radiant flame sensor (radiant sensor)

This part senses if the igniter is hot enough to ignite the flame for heat, allowing the gas valve to open. The sensor is three inches long and is used for many gas clothes dryers. If your dryer is not creating any heat, taking too long to dry or shuts off too soon, you may need to replace the flame sensor. This is a genuine OEM part and is made of both plastic and metal. Please remember to disconnect power to your dryer before starting your repair.

Easy Part #:: EAP11741429

Availability:: In Stock

Price:: $55.03

Igniter kit (glow bar igniter)

This silicon carbide igniter with ceramic holder kit includes the 3-inch flat igniter, mounting bracket, 4-inch wire leads, and the plug. It can replace both round and flat igniters. This kit is used for many gas clothes dryers. This part ignites the gas within the dryer to heat the dryer during the cycle, so if your dryer takes too long to dry, has no heat or not enough heat, you may need to replace the igniter. Be sure to disconnect the power source from your dryer before you do this repair. The igniter is very fragile and should be handled with care.

Easy Part #:: EAP334180

Availability:: In Stock

Price:: $46.56

Drum support shaft - rear shaft with right hand threads (shaft)

Shaft for dryer drum support roller. Rear shaft with left hand threads. Part is updated so nuts may need to be replaced as well on older dryers.

Easy Part #:: EAP11753708

Availability:: In Stock

Price:: $60.57

Push-to-start switch

This is a genuine OEM part. The push-to-start switch is composed of metal and plastic components. Compatible with dryers, the Whirlpool switch powers the appliance after the button is pressed. With a screwdriver, this item is fitted between the bracket and console. The push-to-start switch is sold individually.

Easy Part #:: EAP11742178

Availability:: In Stock

Price:: $22.94

Cover screw (screw)

Sold individually.

Easy Part #:: EAP11740701

Availability:: In Stock

Price:: $9.13

Motor pulley

This part is the replacement motor pulley for your dryer. The motor pulley allows the dryer belt to run straight while the dryer is operating. If your motor pulley is damaged, your dryer may not tumble, and may not start altogether. A damaged motor pulley can also damage the dryer belt, and it may need to be replaced as well. Be sure to disconnect power from the dryer before you begin this repair. This motor pulley is a genuine OEM part sourced directly from the manufacturer.

Easy Part #:: EAP11727942

Availability:: In Stock

Price:: $75.65

Thrust washer

This part is located between the drum support rollers and idler pulley in your dryer to help prevent the parts from bumping up against the brackets they are attached to. If your dryer has a burning smell, is noisy, or will not tumble, you may need to replace the thrust washer. The washer is 3/4 inches in diameter and a is genuine OEM part. It is recommended to disconnect the power to your dryer before you start your repair.