11097589120 Kenmore Dryer Parts List

Search the entire 11097589120 by part description. Keep descriptions simple, e.g. "belt" or "pump". Need help?

Idler pulley

A dryer's idler pulley helps the belt to rotate the drum. It is also known as dryer belt tension pulley wheel.

Easy Part #:: EAP334244

Availability:: In Stock

Price:: $30.97

Door catch kit (door latch kit)

This door catch kit contains two door strikes and three door catches to service dryer doors that have one or two catches. Make sure to read the instructions to determine which one to use for your model. These parts keep the dryer door closed to allow the dryer to operate. If your door won't stay closed or will not start you may need to replace this part. This is a genuine OEM part.

Easy Part #:: EAP334230

Availability:: In Stock

Price:: $5.79

Lint filter (lint screen)

This filter collects lint as it passes through the dryer vent.

Easy Part #:: EAP1491676

Availability:: In Stock

Price:: $70.63

Multi rib belt (drive belt)

This dryer drum belt from Whirlpool/Kenmore has five ridges. It is used for many of Whirlpool's brands of clothes dryers. This flat belt is 1/4 of an inch wide.

Easy Part #:: EAP382430

Availability:: In Stock

Price:: $25.22

M series new style coil kit (valve coil kit)

This gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two-terminal secondary coil. If there is no heat or your drying time is getting longer, the coils may be bad and will need to be replaced. Once the coils go bad they do not hold the gas valve open properly. Usually only one of them burns out but you should replace them as a set. Both must be operational for the gas valve to open. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Easy Part #:: EAP334310

Availability:: In Stock

Price:: $35.50

Leveling foot (leveling feet)

The adjustable leveling leg is used to support and keep your dryer level. It also allows you to adjust the height of your dryer. You may need to replace the leveling leg if one becomes lost, the thread is stripped off, or it is noisy during operation. The leveling leg is almost 2” long, white in color, and made of plastic. There are four leveling legs used on the dryer, please order quantity needed as they are sold individually. This is a genuine OEM part.

Easy Part #:: EAP1609293

Availability:: In Stock

Price:: $9.00

Roller support tri-ring (ring)

The tri ring is used to hold the drum support rollers or the idler pulley onto the shaft. If your dryer will not tumble or is noisy, you may need to replace the tri ring. This is a genuine OEM part and is sold individually.

Easy Part #:: EAP11755850

Availability:: In Stock

Price:: $15.43

Rear drum support roller kit (drum roller support kit)

This drum support roller kit is used for square-ported model clothes dryers. It has a metallic bearing in its center. This support roller is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. If your dryer is noisy, won’t tumble, or takes too long to dry you might need to replace the roller. The kit is a genuine OEM kit and it includes two drum support rollers, four tri rings, and one retaining washer. It is recommended that you replace both rollers at once. Please remember to disconnect the power to your appliance before starting your repair.

Easy Part #:: EAP347627

Availability:: In Stock

Price:: $16.52

Dryer cycling thermostat (internal bias operating thermostat)

The cycling thermostat with an internal bias heater will continually cycle the heating element off and on to maintain a constant inner temperature in the dryer. This cycling thermostat has a limit of 155 degrees Fahrenheit and a differential of 25 degrees. Meaning that the heating element will cut out at 155 degrees and cycle back on once the internal temperature drops by 25 degrees. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting the repair.

Easy Part #:: EAP11741405

Availability:: In Stock

Price:: $32.14

Dryer drum seal with adhesive (seal)

This part seals the drum to prevents air from escaping. This includes silicone rubber adhesive.

Easy Part #:: EAP970088

Availability:: In Stock

Price:: $54.32

Touch-up paint - white (tuchup)

This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, and freezers. This is a genuine OEM part and includes a brush applicator. Please remember to wear gloves to protect your hands when applying this paint.

Easy Part #:: EAP385132

Availability:: In Stock

Price:: $9.20

Blower wheel

The blower wheel pulls air over the heat source, through the clothes drum, and past the thermostats, then pushes it out the exhaust duct. The blower wheel, which is usually plastic, may wear out over time. But if it's noisy, it may simply be clogged with lint. Clean the blower and test to see if the dryer is still noisy. If it is, you probably need to replace it.

Easy Part #:: EAP11743811

Availability:: In Stock

Price:: $81.60

Dryer radiant flame sensor (radiant sensor)

This part senses if the igniter is hot enough to ignite the flame for heat, allowing the gas valve to open. The sensor is three inches long and is used for many gas clothes dryers. If your dryer is not creating any heat, taking too long to dry or shuts off too soon, you may need to replace the flame sensor. This is a genuine OEM part and is made of both plastic and metal. Please remember to disconnect power to your dryer before starting your repair.

Easy Part #:: EAP11741429

Availability:: In Stock

Price:: $55.05

Disposable thermal fuse - two terminal (non-resettable thermal fuse)

This part attaches to the exhaust duct of your clothes dryer.

Easy Part #:: EAP11741444

Availability:: In Stock

Price:: $20.64

Igniter kit (glow bar igniter)

This silicon carbide igniter with ceramic holder kit includes the 3-inch flat igniter, mounting bracket, 4-inch wire leads, and the plug. It can replace both round and flat igniters. This kit is used for many gas clothes dryers. This part ignites the gas within the dryer to heat the dryer during the cycle, so if your dryer takes too long to dry, has no heat or not enough heat, you may need to replace the igniter. Be sure to disconnect the power source from your dryer before you do this repair. The igniter is very fragile and should be handled with care.