Hello!

You're visiting the Easy Appliance Parts site in Canada.

Would you like to shop on the U.S. site?

Go to U.S. site
Stay on this site

41799985840 Kenmore Washer Dryer Combo Parts List

Search the entire 41799985840 by part description. Keep descriptions simple, e.g. "belt" or "pump". Need help?
< PREV 1 2 3 4 5 6 ... 20
1-15 of 294

Rear drum bearing kit (grounding ball clip)

This rear drum bearing kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws. The support bearing helps support the dryer drum to rotate quietly and smoothly during operation. The bearing attaches on the inside of the rear panel of the dryer cabinet. Over time the drum bearing will wear out. This kit will help keep your dryer running as smoothly as possible with as little noise as possible. This is a genuine OEM part. Please remember to disconnect the power before starting your repair.

Easy Part #:
EAP459829
Availability:
In Stock - Ships Today
Price:
$59.23

Upper drum glide (front upper felt glide pad. Includes nylon glides, adhesive, and installation instructions. These drum glides help to support the front of the dryer d)

The upper drum felt glide kit helps to support the front drum as it rotates smoothly and quietly while operating. This kit includes three glides with the adhesive. If your dryer won’t tumble or is noisy, the glide could be worn down causing you to hear a metal on metal noise and will need to be replaced. The drum glide is a genuine OEM part and sold individually. Please remember to disconnect the power to the dryer before starting your repair.

Easy Part #:
EAP470317
Availability:
In Stock - Ships Today
Price:
$39.97

Drum support bearing (rear bearing support for dryer drum.)

The rear drum support bearing helps support the dryer drum to rotate quietly and smoothly during operation. The bearing attaches on the inside of the rear panel of the dryer cabinet. If your dryer is making unusual noises or will not tumble, you may need to replace this part. It is white in color and made of plastic. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Easy Part #:
EAP418807
Availability:
In Stock - Ships Today
Price:
$7.27

Drive v-belt (washer drive belt. If this belt is broken, the washer will not spin or agitate.)

This drive belt is designed to ride on the pulley until the basket gets up to speed. If your washer drum won’t agitate or spin, you may need to replace your belt. It is recommended to disconnect the power to your washer and shut off the water supply before you start your repair. This drive belt is a genuine OEM part.

Easy Part #:
EAP1146950
Availability:
In Stock - Ships Today
Price:
$28.64

Front lower drum seal (lower felt seal, dryer drum front)

This part helps to keep the dryer running as quietly as possible.

Easy Part #:
EAP460194
Availability:
In Stock - Ships Today
Price:
$44.99

Screw

This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. The main reason you would replace this screw is if the old screw is missing or damaged. This part is sold individually and is an OEM part sourced directly from the manufacturer.

Easy Part #:
EAP417463
Availability:
In Stock - Ships Today
Price:
$14.84

Multi-rib drum belt (dryer drum drive belt. The drive belt dries out over time. If the dryer belt cracks or breaks, the dryer will not be able to turn.)

This belt helps rotate from the drive motor to the drum.

Easy Part #:
EAP3408299
Availability:
In Stock - Ships Today
Price:
$19.79

Tub seal assembly (washing machine main tub seal assembly. If the washer leaks then the tub seal may be bad.)

This tub seal helps prevent any leaking around the transmission of your washer. If your washer is leaking you may need to replace the seal. The tub seal is located on the bottom of the outer tub, in the center where the transmission comes through to connect to the agitator. This is a genuine OEM part. Please remember to shut off the water supply and disconnect the power to the washer before starting your repair.

Easy Part #:
EAP459481
Availability:
In Stock - Ships Today
Price:
$88.04

Door strike (strike, dryer door)

The door strike works in conjunction with the dryer door. The male piece of the door strike is the piece that activates the door switch once the dryer door is closed. If your dryer won’t start, or the door won’t open/close, you may need to replace the door strike. This part is made from metal and measures approximately 1 inch. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting your repair.

Easy Part #:
EAP455020
Availability:
In Stock - Ships Today
Price:
$21.53

M series ignition coil kit (dryer gas valve solenoid coil kit. The kit includes both 2 and 3 wire coils. If the dryer does not heat or heats intermittently the gas valve coils ma)

The gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two-terminal secondary coil. If it takes too long to dry or there is no heat, the coils may be bad and will need to be replaced. When the coils go bad they won’t hold the gas valve open properly. Usually only one of them burns out but you should replace them as a set. Both must be operational for the gas valve to open. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Easy Part #:
EAP470049
Availability:
In Stock - Ships Today
Price:
$31.29

Water inlet valve (water inlet valve. The water inlet valve opens to allow hot, cold or warm water to enter the washing machine.)

This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed. If your washer will not stop filling with water, is leaking, or will not fill with water, you may need to replace the water inlet valve. Please make sure to disconnect the power to your washer before you start your repair. This water inlet valve is a genuine OEM part.

Easy Part #:
EAP815509
Availability:
In Stock - Ships Today
Price:
$72.90

Screw-in plastic leveling leg (leveling leg)

Sold individually.

Easy Part #:
EAP1152204
Availability:
In Stock - Ships Today
Price:
$29.80

Agitator (agitator assembly)

The agitator is used in top-loading washing machines to help move the clothes around by rotating back and forth through the detergent and water to wash them. If your agitator won’t agitate or is damaged it will need to be replaced. The agitator is approximately 19” tall with a base diameter of about 13”, white in color and made of plastic. The hub has been changed from a hex to a spline. The agitator drive block and cap must be ordered separately. Please remember to disconnect the power and water supply before starting your repair. This is a genuine OEM part.

Easy Part #:
EAP446533
Availability:
In Stock - Ships Today
Price:
$124.43

Agitator drive block (agitator drive block. If the drive block wears out the washers agitator will not work properly and may also make be noisy during operation.)

The agitator drive block works in conjunction with the agitator in your washing machine by rotating the agitator assembly. If your washer is noisy and not agitating, you may need to replace the drive block because it may be worn out. This part is located between the agitator and the transmission shaft, measures approximately 2” long and is made of metal. This is a genuine OEM part. Please remember to disconnect the power and water supply before beginning your repair.

Easy Part #:
EAP1152574
Availability:
In Stock - Ships Today
Price:
$77.83

Spin bearing (upper spin bearing)

The upper spin bearing works in conjunction with your washer. This part is located on the bottom of the outer tub where the transmission goes up through the middle of the tub. The spin bearing is used to support the transmission shaft in the drive system and allows the transmission shaft to be able to spin freely during the spin cycle. When the spin bearing goes bad it can cause noises during the spin cycle and will need to be replaced. This part is made of metal and is secured by mounting screws. The screws are not included, bearing only. This is a genuine OEM part. Please disconnect the water and power supply before starting the repair.

Easy Part #:
EAP446536
Availability:
In Stock - Ships Today
Price:
$97.67
< PREV 1 2 3 4 5 6 ... 20
1-15 of 294