DCCD330GD0KC Dryer Parts List

Search the entire DCCD330GD0KC by part description. Keep descriptions simple, e.g. "belt" or "pump". Need help?

Drum bearing slide - white (sold individually) (bearing-slide "white")

This single white drum bearing slide attaches to the outer-most sides of the bearing to help support the front of the drum as it rotates. If your dryer is making loud noises or the drum will not tumble, you many need to replace the slides. The manufacturer recommends replacing both slides at the same time; there are 2 slides per dryer. This is a genuine OEM part. Please make sure to disconnect power to the dryer before starting your repair.

Easy Part #:: EAP755842

Availability:: Special Order

Price:: $9.80

M series new style coil kit

This gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two-terminal secondary coil. If there is no heat or your drying time is getting longer, the coils may be bad and will need to be replaced. Once the coils go bad they do not hold the gas valve open properly. Usually only one of them burns out but you should replace them as a set. Both must be operational for the gas valve to open. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Easy Part #:: EAP334310

Availability:: In Stock

Price:: $35.48

Front drum bearing (top bearing)

The drum support bearing helps your dryer operate as quietly as possible by allowing the front of the drum to glide smoothly on the felt seal of the front panel when the drum is rotating. If your dryer is noisy or making a squeaking sound, the slides are probably worn and both slides will need to be replaced. This part measures 10” in height and 19 ½” inside width. Four drum glides are used with the drum support bearing and are sold separately. The support bearing is a genuine OEM part. Please remember to disconnect the power to the dryer before starting your repair.

Easy Part #:: EAP960316

Availability:: Special Order

Price:: $34.33

Drive belt (belt drive)

This dryer drum drive belt is 89.5" long and has four ribs. This part helps spin the drum during the drying cycle.

Easy Part #:: EAP16542496

Availability:: Special Order

Price:: $34.08

Interlock switch (switch interlock)

This switch is multi purpose, for a dishwasher the switch is a simple on/off mechanism that prohibits the appliance from operating when the door is open. For a dryer, this switch will let the dryer know if the belt breaks and shut power off to the dryer. If your dryer will not operate or your dishwasher will not start you may need to replace the switch. This is a genuine OEM part. Please remember to disconnect the power to your appliance before starting your repair.

Easy Part #:: EAP1481922

Availability:: Special Order

Price:: $27.60

Door latch

This part helps to keep the door closed while the machine is running.

Easy Part #:: EAP3502777

Availability:: Special Order

Price:: $13.07

Drum bearing sleeve

Sold individually.

Easy Part #:: EAP266777

Availability:: Special Order

Price:: $8.19

Rear drum bearing kit (shaft & bracket ass'y)

This rear drum bearing kit comes with a shaft, bearing and installation instructions. The bearing plate comes with a slot in it for the ground strap. Over time the drum bearing will wear out, once it has the dryer may make some noise and the drum bearing will need to be replaced. This kit will help keep your dryer running as smoothly as possible with as little noise as possible. This is a genuine OEM part. Please remember to disconnect the power to your appliance before starting your repair.

Easy Part #:: EAP267529

Availability:: No Longer Available

Adjustable leveling screw (levelling screw)

The adjustable leveling screws on the bottom of your dryer can be screwed in or out to lower or raise the leg level. If one of the leveling screws is stripped, damaged, or missing, you may not be able to create a level base for your dryer. The leveling screw has a hexagon-shaped gray plastic foot, with a screw that is approximately 1 inch in length. To replace a damaged screw, simply turn the old screw to the left, until it can be removed. Then, simply screw the new leveling screw into place on the bottom of the dryer, making sure it is the same height as the other 3 leveling screws.

Easy Part #:: EAP1021358

Availability:: Special Order

Price:: $9.97

Door strike (strike door)

TThe door strike for your dryer is mounted on the dryer frame that the door shuts onto. It fits into the door catch on the door and keeps the door closed. If the door strike is damaged or missing, the door will not lock properly and not only will this cause the door to swing open, but it won’t allow the dryer to start properly. It is a small piece of metal, about 1 inch in length and is sold individually.

Easy Part #:: EAP266893

Availability:: Special Order

Price:: $9.81

Retainer o-ring (o ring)

This is a replacement O-ring for the drum bearing retainer on your dryer. The drum bearing is found at the back of the dryer drum. The O-ring is designed to create a seal on the drum bearing. The O-ring is made of rubber, and can occasionally wear down and break. If you notice that your dryer drum bearing is worn while you’re replacing the O-ring, you should consider replacing it as well. This product is sold individually, and is an OEM part from the manufacturer.

Easy Part #:: EAP266776

Availability:: Special Order

Price:: $29.38

Door switch

A door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open.

Easy Part #:: EAP2344321

Availability:: Special Order

Price:: $35.35

Lint filter - white frame (filter frame coin)

The lint filter is used to collect lint and debris as it passes through the dryer vent. It is recommended to clean the lint filter before every load. If your dryer takes too long to dry, the lint filter frame becomes damaged or the filter has torn you may need to replace the lint filter. The frame is white in color. This is a genuine OEM part.

Easy Part #:: EAP11767017

Availability:: No Longer Available

Duct felt seal (felt)

The duct felt seal allows the front of the drum to glide smoothly on the exterior panel while the drum is rotating. The seal is located between the back of the drum and the rear dryer panel. If the heat is escaping from the drum area causing the dryer to run too long or if there are marks on your clothes you many need to replace the duct felt seal. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.