WM3455HW LG Parts List

Search the entire WM3455HW by part description. Keep descriptions simple, e.g. "belt" or "pump". Need help?

Washing machine drain pump (motor assembly,ac,pump)

This drain pump motor helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period. If your washer will not drain, is noisy, leaking, or pumps but will not spin, you may need to replace the drain pump motor. This is a genuine OEM part. Please remember to shut off the water supply and disconnect the power to the washer before starting your repair. Note: Pump casing is not included.

Easy Part #:: EAP3579318

Availability:: In Stock

Price:: $140.89

Water inlet valve - hot (valve assembly,inlet)

The hot water inlet valve is located on the back of the washer and it helps control the amount of water that enters into the washer. The valve has a standard hose fitting inlet, 1 water outlet, 120 volts and 6 watts. If the washer is filling slowly or not at all, the solenoid may have gone bad and you will need to replace the inlet valve. The valve measures approximately 3” L x 2 3/4” W. Please remember to disconnect the water and power to the washer before starting the repair. This is a genuine OEM hot water inlet valve.

Easy Part #:: EAP3527427

Availability:: In Stock

Price:: $68.41

Rear tub gasket

The rear tub gasket is located between the drive shaft and the rear outer tub to form a watertight seal to prevent water from leaking. It is recommended to replace the two bearings at the same time as replacing the tub gasket. The gasket is black in color and measures approximately 3” in diameter. This is a genuine OEM part. Please make sure you disconnect the power and water supply to the washer before starting your repair.

Easy Part #:: EAP3522855

Availability:: In Stock

Price:: $41.27

Washer motor rotor position sensor (sensor assembly)

The sensor monitors the direction and speed of the spinning rotor.

Easy Part #:: EAP11706506

Availability:: In Stock

Price:: $36.41

Door lock assembly (switch assembly,locker)

Easy Part #:: EAP3533609

Availability:: In Stock

Price:: $98.38

Noise filter assembly (filter assembly)

Easy Part #:: EAP3528920

Availability:: In Stock

Price:: $110.72

Bearing,ball

The tub bearing supports the spin basket shaft at the back of the washing tub. If your washing machine will not spin, is leaking water, or if there is a loud screeching noise during the wash cycle, there could be an issue with the tub bearing. This genuine OEM replacement bearing has a 3-inch outer diameter, and is used to help the tub spin smoothly and to stop the washing machine from shaking during the cycle. NOTE: This part is very difficult to install. The manufacturer recommends replacing the complete rear tub and bearing assembly at the same time.

Easy Part #:: EAP7785069

Availability:: On Order

Price:: $73.18

Shock absorber

Sold individually.

Easy Part #:: EAP3522311

Availability:: In Stock

Price:: $53.86

Leg assembly

This levelling leg is a genuine replacement part. It is used to help keep your washing machine stable and balanced. It helps support your appliance. It screws into the base of your washer, and you can thread it in or out to adjust the height. The foot on this leg is made of rubber, which helps with grip, stabilization, and vibration reduction. It is also hexagonal in shape, which allows you to more easily adjust it. This levelling leg features a locknut on the shaft which can be tightened against the bottom of your appliance, this will stop the leg from rotating while you are using your washer. This replacement is sold individually.

Easy Part #:: EAP7788210

Availability:: In Stock

Price:: $45.05

Pump filter (parts assembly)

This replacement pump filter, also known as a filter assembly, is a genuine OEM part for your washer or washer/dryer combo. Before beginning this repair, turn off the power and water supply to your washer. The filter assembly may need to be replaced because it is broken or is leaking water. To locate the filter assembly, pry open the small door on the front of the washer, using a flat-blade screwdriver. Unplug the drain hose next to the filter and drain the water into a bucket. Then unscrew the pump filter, and replace with your new one.

Easy Part #:: EAP3522306

Availability:: In Stock

Price:: $30.74

Cap,drain hose

This drain hose plug, also known as a hose cap, is a genuine OEM part for your washing machine. This plug caps the drain hose from the pump housing, and helps prevent leaks from your washer. Before beginning this repair, make sure the power and water sources to your washer are shut off. To access the pump housing, open the pump filter cover, pull out the drain hose, remove the old plug and replace it, first draining the remaining water from the drain hose.

Easy Part #:: EAP3635866

Availability:: In Stock

Price:: $9.23

Drain hose (hose,pump)

Easy Part #:: EAP3527285

Availability:: In Stock

Price:: $52.79

Hose,connector

This part is the replacement connector hose or clean-out drain hose for your washer. It is black in color and is sold individually. The connector hose drains water out of the washer if the drain cycle is not working. If the hose breaks, it will not be able to drain the water properly, and you may experience a water leak. Be sure to disconnect your washer from the power source, as well as the water source before you begin this repair. This is an OEM part sourced directly from the manufacturer.